Publicidad
Idiomas disponibles
Idiomas disponibles
Table
Table
1) Remove the bracket from below the work table by loosening the two knobs. (Fig.1).
1) Remove the bracket from below the work table by loosening the two knobs. (Fig.1).
Remove the two knobs, bracket and screws.
Remove the two knobs, bracket and screws.
2) Place the work table on the trunnion by guiding the saw blade through the slot in the
2) Place the work table on the trunnion by guiding the saw blade through the slot in the
table. (Fig.2)
table. (Fig.2)
3) Install the table insert in the center of the table. (Fig.3)
3) Install the table insert in the center of the table. (Fig.3)
4) Align the screw holes on the table with the trunnion and secure with the three recessed
4) Align the screw holes on the table with the trunnion and secure with the three recessed
screws, washers and bolts, tighten securely. (Fig.4)
screws, washers and bolts, tighten securely. (Fig.4)
5) Replace bracket under the work table with the two screws and knobs removed from
5) Replace bracket under the work table with the two screws and knobs removed from
step one. (Fig. 5)
step one. (Fig. 5)
6) Attach the rip fence to the table by pushing down on the locking handle. (Fig. 6)
6) Attach the rip fence to the table by pushing down on the locking handle. (Fig. 6)
Note: If the rip fence won't fit on the table turn handle counter clockwise to loosen it.
Note: If the rip fence won't fit on the table turn handle counter clockwise to loosen it.
7) Insert miter gauge by sliding it into the miter gauge slot. (Fig. 7)
7) Insert miter gauge by sliding it into the miter gauge slot. (Fig. 7)
Mounting your saw to a work bench
Mounting your saw to a work bench
Your band saw has four holes for mounting to a work bench. (Fig. 8) Mount on a firm,
Your band saw has four holes for mounting to a work bench. (Fig. 8) Mount on a firm,
stable surface, preferably a work bench.
stable surface, preferably a work bench.
1) Drill four holes on the workbench to match the saw base holes.
1) Drill four holes on the workbench to match the saw base holes.
2) Attach the saw using proper bolts, lockwashers and nuts and tighten securely.
2) Attach the saw using proper bolts, lockwashers and nuts and tighten securely.
Adjustments
Adjustments
Upper blade guide adjustment
Upper blade guide adjustment
WARNING: Unplug saw from power supply.
WARNING: Unplug saw from power supply.
The upper blade guide protects against unintentional contact with the saw blade.
The upper blade guide protects against unintentional contact with the saw blade.
1) Always set the upper blade guide as close as possible to the work piece.
1) Always set the upper blade guide as close as possible to the work piece.
(Max. distance: 1/8"). (Fig. 9)
(Max. distance: 1/8"). (Fig. 9)
2) Adjust the height by loosening the blade guide locking knob (Fig. 10) then adjust height
2) Adjust the height by loosening the blade guide locking knob (Fig. 10) then adjust height
with guide adjustment knob (Fig. 11) then re-tighten blade guide locking knob.
with guide adjustment knob (Fig. 11) then re-tighten blade guide locking knob.
3)The upper blade guide adjustment consists of a thrust bearing that supports the band
3)The upper blade guide adjustment consists of a thrust bearing that supports the band
saw blade from the rear and two guide pins that provide lateral support, these need to
saw blade from the rear and two guide pins that provide lateral support, these need to
be adjusted after every blade change or tracking adjustment.
be adjusted after every blade change or tracking adjustment.
Thrust bearing adjustment (Fig. 12)
Thrust bearing adjustment (Fig. 12)
1) Adjust the thrust bearings by loosening the set screw with allen wrench.
1) Adjust the thrust bearings by loosening the set screw with allen wrench.
2) Adjust the bearing to 1/32' away from the blade. (When the band saw is turned by
2) Adjust the bearing to 1/32' away from the blade. (When the band saw is turned by
hand it should it should not touch the bearing)
hand it should it should not touch the bearing)
3) Tighten set screw.
3) Tighten set screw.
Upper guide pin adjustment
Upper guide pin adjustment
1) Adjust the guide pins by loosening the two set screws. (Fig.13)
1) Adjust the guide pins by loosening the two set screws. (Fig.13)
2) Press the guide pins together against the blade.
2) Press the guide pins together against the blade.
3) Turn the saw wheel by hand clockwise several times to bring the guide pins into the
3) Turn the saw wheel by hand clockwise several times to bring the guide pins into the
correct position.
correct position.
4) Tighten the guide pins set screws.
4) Tighten the guide pins set screws.
(Turn the blade wheel by hand two times to ensure the blade is not pinched)
(Turn the blade wheel by hand two times to ensure the blade is not pinched)
12
12
Publicidad
