Wentronic Goobay 60656 Manual Del Usuario página 5

EN
Bike Powerbank
3 Intended use
We do not permit using the device in other
ways like described in chapter „Description
and Function" or in the „Safety Instructions".
Use the product only in dry interior rooms. Not atten-
ding to these regulations and safety instructions might
cause fatal accidents, injuries, and damages to persons
and property.
4 Preparation
1. Check the scope of delivery for completeness and
integrity.
2. Compare the specifications of all used devices and
ensure compatibility.
5 Mounting
1. Remove the screw from the bike mount.
2. Clamp the bike mount to the frame of your bicycle.
Make sure that the operating elements of the bicycle
are not obstructed.
3. Reinsert the screw of the bike mount and screw it
tight.
4. Slide the power bank into the top of the bike mount.
6 Connection and operation
6.1 Switching the powerbank on and off
• Press the function button 1x briefly to switch on the
power bank.
• Press the function button 2x briefly to switch off the
power bank.
6.2 Charging the powerbank
The powerbank is supplied partially charged. Fully
charge the powerbank before using it for the first time!
1. Connect the USB-C™ socket of the powerbank to a
USB power source via a charging cable.
This can either be a 230 V USB charging adapter, a
12/24 V car USB charger or the USB socket of a PC.
2. Disconnect all cable connections after charging.
6.3 Charging your mobile device
1. Connect your mobile device to the USB-C™ or
USB-A socket.
Your mobile device is charging.
2. Disconnect all cable connections after charging.
6.4 LED indicator
See Fig. 2.
The charging status of the power bank is shown via the
LED indicator. The LEDs light up or flash blue depen-
ding on the battery status. If the QuickCarge function is
active, LED 1 lights up green.
6.5 Switching the LED light on and off
NOTICE!
The LED light is not suitable for illuminating the road
and is not approved for use in road traffic.
The LED light can be used as a key light, for example.
• Press the function button 1x for a long time to switch
on the LED light.
• Press the function button again 1x for a long time to
switch off the LED light.
REV2023-05-24 Subject to change without notice.
V1.1aw
Misuse
7 Maintenance, Care, Storage and
Transportation
NOTICE!
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Charge the batteries every three months to ensure
they maintain capacity when not in use for an exten-
ded period of time.
• Store the product out the reach of children and in a
dry and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.
8 Disposal instructions
8.1 Product
According to the European WEEE directive,
electrical and electronic equipment must not be
disposed with consumers waste. Its compo-
nents must be recycled or disposed apart from
each other. Otherwise contaminative and hazardous
substances can damage the health and pollute the en-
vironment.
As a consumer, you are committed by law to dispose
electrical and electronic devices to the producer, the
dealer, or public collecting points at the end of the devi-
ces lifetime for free. Particulars are regulated in natio-
nal right. The symbol on the product, in the user manu-
al, or at the packaging alludes to these terms. With this
kind of waste separation, application, and waste dispo-
sal of used devices you achieve an important share to
environmental protection.
WEEE No: 82898622
8.2 Packaging
Packaging can be disposed of free of charge at
the suitable collection points – paper belongs in
paper bins, plastics belong in yellow sacks and
glass belongs in used glass bins.
DE4535302615620
9 EU Declaration of conformity
With the CE sign Goobay®, a registered
trademark of the Wentronic GmbH ensures,
that the product is conformed to the basic
European standards and directives.
- 5 -
Pillmannstraße 12 | 38112 Braunschweig | Germany
60656
Material damage
Goobay® by Wentronic GmbH