Kärcher K 5 Smart Control Manual Del Usuario página 16

Push the high-pressure hose through the
hose guide
1. Insert the high-pressure hose through the hose
guide from the rear.
Illustration K
Installing the water connection coupling
1. Screw the water connection coupling onto the water
connection on the device.
Illustration L
Initial Start-Up
Note
If you do not want to control the device by mobile device
®
via a Bluetooth connection, you only have to follow the
steps in the section "Connecting the high-pressure
gun".
Download the app and register your device
1. Download the KÄRCHER Home & Garden app (see
chapter KÄRCHER Home & Garden app).
2. Start the KÄRCHER Home & Garden app.
3. Log in to the KÄRCHER Home & Garden app. If
necessary, create an account for this.
4. Scan the enclosed QR code.
The high-pressure cleaner is registered.
Note
If you do not have the enclosed QR code at hand, you
can also register the device with the part number and
serial number. Both numbers are given on the type
plate.
5. Follow the instructions of the KÄRCHER Home &
Garden app.
Note
Be sure to do this before connecting the high-pressure
®
gun Bluetooth Activate on your mobile device.
Connecting the high-pressure gun
Note
You can find a detailed description of the connection at
https://www.kaercher.com/FCR.
6. Plug the mains plug for the high-pressure cleaner in-
to a socket.
The device switches to coupling mode for 60 s. Dur-
ing this time it is possible to couple the high-pres-
sure gun.
7. Press the "+" key and the "-" key on the high-pres-
sure gun simultaneously for at least 3 s.
If the coupling is successful, the pressure levels, as
well as the radio and the Bluetooth
shown on the display.
Illustration M
®
The Bluetooth connection between the mobile de-
vice and the high-pressure cleaner is established
automatically.
Note
If necessary, you can also establish the Bluetooth
nection at a later time by pressing the "-" key for 10 s.
8. If the coupling attempt failed:
a Pull the mains plug for the high-pressure cleaner
out of the socket.
b Wait 20 s.
c Couple the high-pressure gun again.
Initial startup
1. Place the device on a flat and level surface.
2. For devices with a hose reel: Completely unwind the
high-pressure hose from the hose reel.
3. For devices without a hose reel: Unwind the high-
pressure hose completely and eliminate any loops
16
4. Pull the high-pressure hose all the way forwards
5. Insert the high-pressure hose into the high-pressure
Note
Take care to ensure the correct alignment of the nipple.
6. Check for a secure connection by pulling on the
7. Plug the mains plug into a mains socket.
For the connection values, see the type plate or chapter
Technical data.
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water
Contamination in the water can damage the pump and
the accessories.
KÄRCHER recommends using the KÄRCHER water fil-
ter for protection(special accessory, order number
4.730-059).
ATTENTION
Hose coupling with Aquastop on the water connec-
tion of the device
Damage to the pump
Never use a hose coupling with Aquastop on the water
connection of the device.
You can use an Aquastop coupling on the tap.
1. Plug the garden hose onto the water connection
2. Connect the garden hose to the water line.
3. Open the water tap fully.
When used with the KÄRCHER suction hose with check
valve (special accessory, order number 2.643-100) this
high-pressure cleaner is suitable for sucking up surface
water, e.g. from rain barrels or ponds (for the maximum
suction height see chapter Technical data).
The water connection coupling is not required for vacu-
uming operation.
1. Fill the suction hose with water.
2. Screw the suction hose onto the device water con-
®
symbol, will be
1. Switch the device on "I/ON".
2. Unlock the lever of the high-pressure gun.
3. Press the lever of the high-pressure gun.
®
con-
4. Allow the device for run a maximum of 2 minutes un-
5. Release the lever of the high-pressure gun.
6. Lock the lever of the high-pressure gun.
ATTENTION
Pump running dry
Damage to the device
If pressure does not build up in the device after 2 min-
utes then switch the device off and proceed according
to the instructions in chapter Troubleshooting guide.
English
and twists.
through the hose guide.
gun until it audibly latches into place.
Illustration N
high-pressure hose.
Water supply
Connection to the water line
coupling.
Illustration O
Sucking water from open containers
nection and hang it in a water source (e.g. water
butt).
Vent the device
The device switches on.
til the water escaping from the high-pressure gun is
free of air bubbles.
Operation