Publicidad
Idiomas disponibles
Idiomas disponibles
DESCRIPTION
The Craftsman Coil Utility Nailer drives full head nails from
1_/4"to 2W' long. Magazine will hold a coil of 400 wire
collated nails. Safety feature disables tool unless contact trip
is pressed against workpiece. Sequential trigger switch allows
selection of rapid-fire or single-fire mode. Contact trip can be
adjusted for setting nail depth. Plastic protector on the end of
contact trip prevents marring of workpiece. Air deflector can
be adjusted to any direction. Die cast aluminum body with
textured rubber grip minimizes operator fatigue and makes
nailer lightweight and durable. The coil utility nailer is excellent
for siding, sheathing, exterior trim, subflooring, decking and
fencing.
SPECIFICATIONS
Capacity .....................
400 wire collated coil nails
Nail size .......................
0.082 to .110" diameter
Nail lengths ...............................
1_ to 2_/2 ''
Operating pressure ........................
65-110 PSI
Air inlet ...................................
W' N.P.T.
Length .......................................
103/4 ' '
Height .......................................
11%"
Width ..........................................
5"
Weight .....................................
4.2 Ibs.
NAILS
18081 (Box of 8000) ...........
Galvanized nails, 13/4 ' ' long
18082 (Box of 6000) ............
Galvanized nails, 2" long
AIR SUPPLY
LINE
Refer to Figure 1.
DANGER:
De not use oxygen, carbon dioxide, high-pressure
compressed gas or bottled gases as the power source for this
tool. The tool will explode and serious personal injury could
result.
•
The air tool operates on compressed
air at pressures from
65 to 110 PSI.
•
Never connect the tool to air pressure which could poten-
tially exceed 200 PSI. Use only clean, dry, regulated air
within rated range as marked on tool.
Air Delivery
Required:
1.87 SCFM @ 90 PSI
(30 shots per minute).
WARNING:
Keep hands and body away from discharge area
of tool when connecting air supply. Always disconnect tool
from air supply when servicing or adjusting tool and when tool
is not in use.
•
Air operated tools require clean, dry, lubricated com-
pressed air to ensure top performance,
low maintenance
and long life.
•
Dirt and abrasive materials present in all air lines will dam-
age tool O-rings, valves and cylinders.
•
Moisture will reduce tool performance and life if not
removed from compressed
air.
•
A filter-regulator-lubricator
system is required and should be
located as close to tool as possible. A distance of less than
15 feet is recommended.
•
Keep air filter clean. A dirty filter will reduce the air pressure
to the tool causing a reduction in power and efficiency.
•
The air supply system must be able to provide air pressure
of 65 to 110 pounds per square inch at tool.
°
All hoses and pipes in the air supply system must be clean
and free of moisture and foreign particles. Hoses must be
rated for a maximum working pressure of 150 PSI or 150%
of maximum system pressure, whichever is greater.
°
Do not mount swivel connector in air supply line.
°
The air pressure should be properly regulated.
°
Different workpiece materials and different fastener lengths
will require different operating pressure.
°
Be sure all connections in air supply system are sealed to
prevent air loss.
°
Never connect a female quick-disconnect
coupling to the
tool side of air line connection. A male, free-flow coupling
should be connected to the tool side of air line connection
(see Figure 1).
WARNING:
The female coupling provides a seal preventing
loss of compressed
air from compressor tank when discon-
nected from male coupling. If connected to tool side of air
supply, the female coupling could seal a compressed
air
charge in the tool which could discharge if the tool trigger is
actuated.
I
Male Connector
Female Connector
Figure 1 - Air Supply Line
LOADING
Refer to Figures 2 through 6, (pages 3 and 4).
WARNING:
Disconnect tool from air supply. Do not load tool
until you are ready to use it. Do not pull trigger or depress
contact trip while loading tool. Always load with nose of tool
pointing away from you and others. Always wear safety gog-
gles that comply with United States ANSI Z87.1.
NOTE: For best results, use Sears fasteners only.
•
Push the door latch down and swing the door open; then
swing the magazine cover open (see Figure 2).
Figure 2 - Opening
the magazine
Publicidad
