Publicidad
Idiomas disponibles
Idiomas disponibles
Manually
Lighting
Your Grill By Paper
Match
To light your gas grill by match, insert a match into the Lighting
Stick and follow steps 1 through
5 of the Grill Lighting
Instructions. Then, light the match and place Lighting Stick
through the Cooking Grid on the grill as shown below. Turn
the nearest Control Knob to the HI setting to release gas. The
Burner should
light immediately.
Match
'\
\
\
\
\
Lighting
Stick
(Note: the Lighting
Stick is placed
in the drawer.)
Never lean over the grill cooking area while lighting
your gas grill. Keep your face and body a safe distance
(at least 18 inches) from the front of grill when lighting
your grill by match.
Should a FLASHBACK fire occur in or around the
Burner Tubes, follow the instructions below. Failure
to comply with these instructions could result in a
fire or explosion that could cause serious bodily
injury, death, or property damage.
•
Shut off gas supply to the gas grill.
•
Turn the Control Knobs to OFF position.
•
Open the Grill Lid.
•
Put out any flame with a Class B fire
extinguisher.
•
Once the grill has cooled down, clean the
Burner Tubes and Burners according to the
cleaning instructions
in this Use and Care
Guide.
If ignition does not occur in 5 seconds, turn the Control
Knob(s) and gas source OFF and conduct a leak test
as explained in the Use and Care section of this guide.
If no leaks are detected, wait 5 minutes for any gas
to clear and repeat the lighting procedure.
To
the
[]
[]
[]
[]
[]
[]
[]
[]
[]
17
Troubleshooting
If the grill fails
to light :
1. Turn gas offat source and turn Control Knobs to OFF. Wait
at least 5 minutes for gas to clear, then retry.
2. If your grill still fails to light,
check
gas supply
and
connections.
3. Repeat lighting procedure.
If your grill still fails to oper-
ate, turn the gas off at source, turn the Control Knobs to
OFF, then check the following:
[] Misalignment of Burner Tubes over Orifices
Correction:
Reposition Burner Tubes over Orifices.
[] Obstruction
in gas line
Correction:
Remove fuel line from grill. Do not smoke! Open
gas supply for one second to clear any obstruction from fuel
line. Close off gas supply at source and reconnect fuel line
to grill.
[] Plugged
Orifice
Correction:
Remove Burners
from grill by removing the
screw from the rear of each Burner using Phillips Head
Screwdriver. Carefully lift each Burner up and away from
gas valve Orifice. Remove the Orifice from gas valve and
gently clear any obstruction with a fine wire. Then reinstall
all Orifices, Burners, screws and cooking components.
[] If an obstruction is suspected
in Gas Valves or Manifold,
call the Grill Information Center
1-888-317-7642
8am to
8pm CST, Monday through Friday.
[] Obstruction
in Burner Tubes
Correction:
Follow the Burner Tube cleaning procedure on
page 22 of this Use and Care Guide.
[] Misalignment of Ignitor on Burner
Correction:
Check for proper position of the Electrode Tip
as shown in steps 5 & 6 on page 10. The gap between
the Spark Electrode Tip and
Spark Receiver
should be
approximately
3/16". Adjust
if necessary. With the gas
supply closed, turn any Main Burner Control Knob _, to
then push in and watch for the presence of a spark at the
Electrode.
[] Disconnected
Electric Wires
Correction:
Inspectthe Ignitor Junction Boxfound behind the
Control Panel. Connect loose Electric wires to Junction Box
and try to light the grill.
[] WeakAA battery
Correction:
Unscrew the Ignitor Cap and replace the bat-
tery.
[] If the grill still does not light you may need to purge
air from the gas line or reset the regulator
excess gas
flow device. Note: This procedure should be done every
time a new LP Gas tank is connected
to your grill.
purge
air from
your
gas
line
and/or
reset
regulator
excess
gas flow
device:
Turn Control Knobs to the OFF position.
Turn off the gas at the tank valve.
Disconnect
regulator
from
LP Gas tank.
Let unit stand
5 minutes to allow air to purge.
Reconnect
regulator
to the LP Gas tank.
Turn tank valve on SLOWLY
1/4 of a turn.
Open the Grill Lid.
Push and
to _, and
burner
is
turn the Left Main Burner Control Knob
you will hear a clicking sound
as the
being
ignited.
Once the burner is lit, turn the knob back to HI.
Publicidad
