Defort BFP-60N Instrucciones De Servicio página 9

E
Never start or stop the spray gun while it is aimed at
the surface to be sprayed. Evenly control the speed of
movement of the spray gun. A fast speed of movement
over the surface will give a thin coat and aslowspeed
will givea heavy coat. Apply one coat at a time. If a fur-
ther coat is required, make sureyou observe the manu-
facturers drying time recommendations before apply-
ing a second coat. When spraying small areas, keep
the output control on a low setting. This will avoid using
too much paint and prevent overspray. Where possible,
avoid stopping and starting when spraying an object.
This can lead to too much, or not enough paint being
applied. Do not tip the spray gun to more than 45°
CLEANING AND MAINTENANCE
Always remember to disconnect from the
mains supply before cleaning the spray gun
or paint container.
It is essential that the spray gun is cleaned thoroughly
after every use. Failure to clean it will almost certainly
result in blockages and it may not operate when you
next come to use it! The guarantee does not cover
cleaning a sprayer that has not been properly cleaned
by the user.
The following action must be taken after every
use.
1. Empty any remaining material from the container.
2. Clean the container thoroughly with the thinner
thatwas used.
3. Pour some thinner into the container and spray
through the spray gun until only clean thinner is
coming out of the nozzle.
4.Thoroughly clean the paint pick uppipeand fi lter with
thinner.
5.Clean the basket and nozzle and remove any other
debris or paint that remains.
6. Turn the spray gun upside down and apply a few
drops of light oil to the two apertures (F). This will
lubricate the piston and cylinder.
If your spray gun should require extra internal
cleaning, it may be necessary to disassemble it. If
so the following action should be taken.
1. Remove the plug from the mains socket.
2. Remove paint container, pick up pipe and fi lter.
3. Release the nozzle (H), valve (j), piston (K) and
spring (L).
4. Clean the cylinder (M) and all parts thoroughly with
solvent.
5. Apply a few drops of light lubricating oil to the pis-
ton, springand cylinder.
6. Reassemble the spray gun.
TROUBLE SHOOTING
Motor hums but does not spray or irregular spray-
ing.
1. Worn swirl head
Replace swirl head.
2. Pick up pipe not into the right position
Re-adjust pick up pipe.
3. Blocked pick up pipe
Clean with thinner.
4. Blocked nozzle
Clean nozzle.
5. Blocked fi lter
Clean with thinner.
6. Control knob needs adjustment
Adjust.
F
Atomization is not good.
1. Volume adjustment is not correct.
Adjust
2. Paint too thick
Check viscosity of the paint
Over painting.
1. Spray gun not clean, or not lubricated, resulting in
piston being stuck in cylinder
Disassemble spray gun and dean with thinner.
2. Too much paint
Adjust the volume clockwise to reduce spraying.
Two t/i/n coats are better then one thick coat.
3. Viscosity too low
Check viscosity
Motor louderthan normal.
1. Spray gun not clean, or not lubricated, resulting in
piston being stuck in cylinder
Disassemble spray gun and clean with thinner.
No spray, no sound.
1. No electricity
Check power supply.
Operating sound not right.
1. Poor output adjustment
Re-adjust
2. Not enough paint in the container resulting in air
being sucked in.
Refi ll with paint
3. Not diluting properly or not passing pick up pipe
completely.
Check pick up pipe and viscosity level.
«Orange Skin» excessive fogging.
1. Incorrectsolventis used
Use correct solvent
2. Spray gun too far from the surface.
Hold spray gun closer to Vie object
3. Paint too thick
Thin the paint
GB
9