Publicidad
Idiomas disponibles
Idiomas disponibles
EN
� Never operate the planer when the
blade is in contact with the work piece.
Only touch the cutting blade on the
work piece after reaching the maximum
speed of rotation;
� Do not use the planer if there are
cloths, fabrics, cables, wires or similar
objects in the work area;
� Do not tilt the planer, thus avoiding
unwanted planning marks;
� Move the planer towards the fibres of
the wood;
� After turning the planer off, the rotary
attachment will continue to move for
a short period of time. Never lay the
planer before the rotary accessory is
completely stopped;
4.1 - AdJUSTING THE dEPTH
Of CUT (fIG. G)
The cutting depth can be set between
0 - 3 mm.
1. Turn the cut depth adjustment knob
(6) to the desired depth;
The arrow at the bottom of the
adjustment handle indicates the depth
selected in the cut depth scale (5);
At start of work, always select a
small depth of cut and test on
the work piece. Repeat until the desired
depth is reached;
4.2 - AdJUSTING THE
PARALLEL GUIdE (fIG. H)
The parallel guide is used to ensure
the execution of a roughing parallel to
the edge (edge) of the work piece. The
cutting width can be set between 0 -
82 mm.
1. Unscrew the fixing screw of the
parallel guide (13);
2. Adjust the guide according to the
desired cutting width. The cut-off width
value is indicated by the end of the
parallel guide support (2), on the scale
of the parallel guide scale (12);
3. Tighten the fixing screw;
4.3 - AdJUSTING THE NOTCH
dEPTH AdJUSTER (fIG. I)
The notch depth adjuster ensures that
the desired depth is not exceeded
during use. The depth of the notch can
be set between 0 - 18 mm.
1. Unscrew the fixing screw of the notch
depth adjuster (17);
2. Adjust the attachment to the desired
depth. The value of the depth of cut is
indicated by an arrow on the scale of
the adjustment accessory;
3. Tighten the fixing screw;
4.4 - STARTING ANd
STOPPING THE PLANER (fIG. J)
1. Lean the support base front plate
(20) on the work piece;
2. Press the lock/unlock button
(8) and the "ON/OFF" switch (7)
simultaneously;
If you do not press the lock/unlock
button, the "ON/OFF" switch will
remain locked.
3. Let the blade reach full speed;
4. Push the planer in the direction
of the work piece continuously and
smoothly, always with the parallel
guide (1) against the edge of the work
piece;
5. To turn off the planer lift it off the
surface of the work piece and release
the "ON/OFF" switch;
Ensure that the blades are not
in contact with the work piece
before turning the "ON/ OFF" switch
on.
4.5 - CHAMfERING THE
EdGES (fIG. K)
The front plate of the support base has
a V-groove that allows the edges to be
chamfered.
1. Select the desired depth of cut in the
adjustment knob (6);
2. Lean the V-groove (21) on the edge
to be chamfered;
3. Press the lock/unlock button
(8) and the "ON/OFF" switch (7)
simultaneously;
If you do not press the lock/unlock
button, the "ON/OFF" switch will
remain locked.
4. Let the blade reach maximum
speed;
5. Push the planer in the direction of
the work piece continuously;
6. To turn off the planer lift it off the
surface of the work piece and release
the "ON/OFF" switch;
Before chamfering the edge of
the work piece, perform a
depth test on the edge of a piece of
wood;
5. MAINTENANCE
INSTRUCTIONS
Before carrying out any cleaning,
adjustment, replacement, repair or
maintenance work, turn off the power
and disconnect the power cord from
the power outlet. Wait for the rotary
accessory to stop completely.
The planer does not require any
additional lubrication or maintenance.
However, regular cleaning should be
carried out to ensure continuous and
trouble-free operation.
Always keep cutting blades clean and
sharp. Properly maintained cutting
blades jam less frequently, control
more easily and allow greater efficiency
when using planer.
Keep the rotating attachment and blade
support base always clean to ensure
cutting accuracy.
31
Publicidad
