Craftsman 351.249510 Manual Del Operador página 4

Refer toFigures 1-9.
CAUTION: Donot a ttempt assembly ifparts aremissing.
Use this manual toorder r eplacement parts.
• Remove allcomponents from theshipping carton a nd verify
against the parts listabove. Clean e ach component and
remove shipping preservatives (coatings) as
required.
NOTE: Before assembling copy crafter, make sure that lathe
is secured to a suitable workbench or stand.
ATTACH TOOL REST BASE {MODEL 24951)
Refer to Figure 2.
• Loosentool rest base lockingbar and slidetool rest base
(suppliedwith the lathe)to as near the headstockas possible,
• Loosen locking handle of lathe tool rest and remove tool rest
(suppliedwith lathe).
• Loosentailstookhandle and remove tailstookfrom lathe bed.
• Insert guide between bed ways. Slide carnage support
through slotof guideand secure with set screw.
• Loosen hex nut from the bottom of tool rest base assembly
supplied with copy crafter so that the clamping plate can
slide between bed ways, Attach locking handle to tool rest
base.
• Slide tool rest base onto lathe bed, Positiontool rest bases
approximately 30" apart, Tool rest base will later be adjust-
ed closer or further apart, depending upon the length of
the workpieca.
• Replace tsilstock onto lathe bed and secure it by tightening
lockinghandle.
_/TOOl Rest
_Carriage Screw
J Guide
:" Tailstock
/J _to_H_a
Ta ndle
Lockin,
Bar
Tool Rest
Locking Handle
Figure 2 - AttachTool Rest Base to Lathe Bed (Model 24951)
ATTACH TOOL REST BASE (MODEL 24952)
Refer to Figure 3.
Loosentailstocklockinghandle and slide it towardthe rear of
the lathe bed tube.
Loosentool rest lockinghandle and slidetool rest base
assembly(suppliedwith the lathe)to as near the headstock
as possible.
Loosenthe lockinghandle of the tool rest holder and remove
toolrest (suppliedwith lathe).
Place tool rest support and bracket onto lathe bed tube
and assemble together using two 8 x 25mm socket head
bolts and two 8ram lock washers.
Position tool rest bracket and support assembly approxi-
mately 30" from the tool rest base supplied with lathe. Tool
rest bases will later be adjusted closer or further apart,
depending upon the length of the workpiece.
Insert brasspin intothreaded hole at toolrest supportand
then thread locking handle into the support.
Place tool rest holderontotool rest supportand secure in
positionusingone 8 x 30ram sockethead boltand spacer.
Thread lockinghandle intotool rest holder.
Socket H::dac::J_.
Tool Rest Holder _
Head Bolt
_'_ Looki ng
t, Handle
\Pin
Tool Rest Bracket
Loc_k W asher
Figure 3 - AttachTool RestBase to Lathe Bed (Model 24952)
INSTALL SUPPORT BARS IN CARRIAGE ASSEMBLY
Refer to Figure 4,
• Remove gear assembly from carriage assembly by
removingthree sockethead bolts.
• Slide supportbars into carriage assembly.
• Replace gear assembly into the carriage and secure in
positionwith socket head bolts,
_L.f Gear Assembly
'_'_Socket Heed Belt
sT.
Assembly
Support Bar
with Rack
Figure 4 - Install Support Bars
Bar
4
INSTALL COPY CRAFTER ONTO LATHE
Refer to Figure 5,
• Slide brackets onto support bars,
• Place spacers over bottom of bracketsand then insert
brackets into tool rest bases,
• Secure bracketsto supportsbars with 8 x 40ram socket
head bolts,
BsmpCkce_ r_!_ d Bolt
Figure 5 - Install Copy Crafterto Lathe