Publicidad
Idiomas disponibles
Idiomas disponibles
Operation
Switching On / Off
• Press the
button to switch on the appliance. The fan
starts to operate. The control lamp FAN lights up.
• Press the
button again to switch off the appliance. If
the heating mode was active, the FAN mode is activated
for 30 seconds and the air flap is closed. The appliance
then switches to standby mode.
Swivelling the Air Flap
Press the
button to switch the air flap swinging on or
off. The control lamp SWING lights up when the function is
activated.
Heating Function
Press the
button repeatedly to switch between the
following modes:
LOW = Low temperature and fan.
Control lamp LOW and FAN light up.
HIGH = High temperature and fan.
Control lamp HIGH and FAN light up.
FAN = Only the fan is active.
Control lamp FAN light up.
Setting the Temperature (TEMP Function)
The appliance automatically selects the heating level ac-
cording to the set temperature. As soon as the set tempera-
ture is reached, the appliance switches off the heating.
The adjustable temperature range is between 18 °C and
45 °C.
1. Press the
button.
2. Set the desired temperature with the
3. Confirm the entry with the
OK
perature level is automatically maintained.
The control lamp TEMP lights up. This indicates that the
function is activated.
Deleting the Set Temperature
Proceed as follows to delete the previously set temperature:
1. First press the
button.
2. To delete the setting, now press the
control lamp TEMP goes out.
Timer Function
You can set the appliance to operate for a certain time.
1. Press the
button repeatedly to select between one
hour ( ) and eight hours (
bles the function.
2. After the set time has elapsed, a beep sounds and the
appliance starts a 30-second countdown. The appliance
switches to standby mode after the countdown has
elapsed.
14
PC-HL3116_IM
and
buttons.
button. The desired tem-
button. The
C ° °
). The setting (
) disa-
- The activated function is not displayed for technical
reasons.
- The function cannot be selected when the weekly timer
is active.
Setting the Weekly Timer
• The weekly timer cannot be set when the appliance is in
fan mode.
• The weekly timer can also be combined with the TEMP
function, the SWING function and the "Open Window
Detection" function.
• To use the weekly timer, you must first set the current
time. The current time must be set when the appliance
is first put into operation and every time the appliance is
disconnected from the mains.
• The days of the week are indicated by the following digits
in the display:
Monday
=
Tuesday
=
Wednesday
=
Thursday
=
Set the Current Time:
1. Press the
button. The indication
pears in the display.
2. Select the current day of the week with the
button. Confirm the entry with the
3. Entering the hours:
appears in the display. The setting is made with the
/
buttons. Confirm the entry with the
4. Enter the Minutes:
appears in the display. The setting is made with the
/
buttons. Confirm the entry with the
Select the Weekly Timer:
• The appliance has pre-programmed week timers (
) and an individually programmable week timer (
• With the weekly timer
, the setting must be made for
all days of the week. Only hours can be set, not minutes.
The stop time must be after the start time.
• If the weekly timer is set in the selected mode, the appli-
ance runs until the stop time. Outside the selected mode,
the fan continues to run for 30 seconds. After that, the
appliance switches to standby mode.
• The activated function is indicated by the control lamps
24 / 7 and LOW or HIGH flashing. As soon as the appli-
ance switches on, the control lamps light up.
• The following is a list of the pre-programmed weekly
timers:
Mode
Weekdays
Monday – Sunday
Monday – Sunday
Monday – Friday
Friday
=
Saturday
=
Sunday
=
(Monday) ap-
or
button.
OK
button.
OK
button.
OK
to
).
Time
8:00 – 17:00
18:00 – 7:00*
8:00 – 17:00
29.06.23
Publicidad
