Publicidad
Idiomas disponibles
Idiomas disponibles
DE
e)
Reparatur und Wartung von Geräten dürfen nur
von qualifiziertem Fachpersonal und mit Original-
Ersatzteilen durchgeführt werden. Dadurch wird die
Sicherheit bei der Nutzung gewährleistet.
f)
Um die vorgesehene Betriebsintegrität des Gerätes
zu gewährleisten, dürfen die werksmäßig montierten
Abdeckungen
oder
Schrauben
nicht
entfernt
werden.
g)
Beim Transport und beim Verlegen des Gerätes
vom
Aufbewahrungsort
zum
Einsatzort
die
Sicherheits-
und
Hygienevorschriften
die manuelle Handhabung für das Land zu
berücksichtigen, in dem das Gerät verwendet wird.
h)
Mit dem Gerät dürfen nur Werkstücke mit Parametern
gemäß den Daten aus der Tabelle der technischen
Daten bearbeitet werden. Das zulässige Ausmaß des
zu bearbeitenden Stoffes nicht überschreiten.
i)
Keine zwei Werkstücke auf einmal bearbeiten.
j)
Lange Werkstücke müssen für die Bearbeitung
abgestützt und stabil sein.
k)
Das Gerät auf einer stabilen, trockenen und flachen
Fläche mit einer Größe montieren, die entsprechend
zum Ausmaß des Geräts und des zu bearbeitenden
Stoffes passt.
l)
Der Boden am Arbeitsplatz muss rutschhemmend
sein.
4
sind
für
Rev. 29.06.2021
U S E R M A N U A L
LEGEND
Read instructions before use.
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation (general
warning sign).
Wear protective goggles.
Wear protective gloves.
Wear foot protection.
CAUTION! Sharp elements. Limb cut hazard.
ATTENTION! Danger of hand crushing.
Only use inside.
SAFETY AT THE WORKPLACE
a)
Make sure the workplace is orderly and well lit.
A messy or poorly lit workplace may lead to accidents.
Try to anticipate what may happen, observe what is
going on and use common sense when working with
the device.
b)
This device is not intended to be used by persons
(including children) with limited physical, sensory
or mental aptitude or lack of experience and/
or knowledge, unless they are supervised by a
person responsible for their safety or have received
instruction from this person as to how the device is
used.
c)
This device is not intended to be used by persons
(including children) with limited physical, sensory
or mental aptitudes or lack of experience and/or
knowledge, unless they are supervised by a person
responsible for their safety or have received instruction
from this person as to how the device is used.
d)
This device may be operated by physically fit persons
who are properly trained and able to handle the
device and who reviewed this operating manual and
received training in occupational health and safety.
e)
In case of doubt whether the product operates
correctly or finding damage please contact the service
centre of the manufacturer.
f)
Only the service centre of the manufacturer can make
repairs of the product Do not attempt to make repairs
yourself!
g)
Children or unauthorised persons are forbidden from
entering a work station. (A distraction may result in
a loss of control over the device).
h)
During workpiece working, take care of strangers and
their safety.
i)
Observe the workpiece carefully during working to
avoid its damage and prevent any possible hazard.
j)
Maintain order and remove any dust, debris and
waste material after working.
k)
If more elements are manufactured, they should be
stored in such a way before and after working that
allows keeping order at the workstation.
REMEMBER! When using the device, protect
children and other bystanders.
PERSONAL SAFETY
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which can
significantly impair the ability to operate the device.
Rev. 29.06.2021
EN
b)
When working with the device, use common sense
and stay alert. Temporary loss of concentration whilst
using the device may lead to serious injuries.
c)
Use personal protection equipment as required
for working with the device, specified in section 1
(Legend). The use of correct, approved personal
protection equipment reduces the risk of suffering an
injury.
d)
Do not overestimate your abilities. When using the
device keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
e)
Do not wear loose clothing or jewellery. Keep hair,
clothes and gloves away from moving parts. Loose
clothing, jewellery or long hair may get caught in
moving parts.
f)
Before device operation, remove all regulating tools
or wrenches. Any tool or wrench left inside a rotating
part of the device can result in injuries.
g)
The material to be worked should be free of impurities.
h)
Do not touch movable parts or accessories during
device operation.
i)
Use protective gloves to avoid being hurt by sharp
edges.
j)
Do not work elements made of hard materials.
k)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
SAFE DEVICE USE
a)
Do not overload the device. Use appropriate tools for
the given task. A correctly selected device will perform
the task for which it was designed better and in a safer
manner.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c)
Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of the
device. If damage is discovered, hand over the device
for repair before use.
d)
Keep the device out of the reach of children.
e)
Device repair or maintenance should be carried out by
qualified persons, only using original spare parts. This
will ensure safe use.
f)
To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
g)
When transporting and handling the device between
the warehouse and the destination, take into account
the occupational health and safety principles for
manual transport operations which apply in the
country
h)
Use the device to work elements of parameters
conforming with the data given in the technical data
table. Do not exceed the permissible dimensions of
the worked material.
i)
Do not work two workpieces at the same time.
j)
Long workpieces must be supported and set stably for
working.
k)
Mount the device on a stable, dry and flat surface of a
size that is adapted to the device and worked material
overall dimensions.
l)
The floor at the workstation should be anti-slip
5
Publicidad
