Blackstone PRO Serie Manual Del Propietário página 15

SYMPTOMS
01. Burner will not Light with ignition system
Model 2006
02. Pressing the ignitor button does not result in a clicking sound
If ignition does not occur in 5 seconds, turn the burner controls off, wait 5
minutes and repeat the lighting procedure.
If this does not work, to determine the cause, please try to ignite your griddle
with a match. (Please reference the Match Lighting Instructions in the
Cleaning the Burner Assembly section of the Care & Maintenance chapter.)
FIRST TIME CLEANING
S T E P 14
Use the two (2) pre-in-
stalled M6x12 screws in the hood
Blackstone Griddles are pre-treated
handle to install the hood handle
with cooking oil to prevent rust and
If you CAN ignite your griddle with a match
and two (2) mica sheets to the front
damage during shipping. For first
of the hood.
time use, wash griddle with hot,
POSSIBLE CAUSES
soapy water.
Insert one (1) AA battery (not
01. Dead battery or no battery.
included) under the ignition button.
THIS IS THE ONLY TIME YOU
SHOULD USE SOAP ON THE
02. Battery installed incorrectly.
GRIDDLE COOKING SURFACE.
Rinse and dry completely. Proceed
03. Ignitor wire misaligned.
with seasoning instructions. (Please
reference the Griddle Seasoning
Instructions section.)
S T E P 15
04. Damage to the ignition system.
Connect the propane tank (not included) and set it on the cart
PROTECTING YOUR
base. Tighten the cart base wing screw to secure. (Please reference the
GRIDDLE TOP
Connection & Removal section of the Fuel chapter.)
Store griddle in a cool, dry loca-
If you CAN NOT ignite your griddle with a match
tion. Always cover griddle if stored
outdoors. Choose from a variety of
POSSIBLE CAUSES
griddle covers offered by Blackstone.
05. Burner tubes are not receiving fuel.
When protecting griddle with soft
cover, use the "tenting" method to
prevent water from accumulating
on griddle top. "Tenting" involves
placing an object (a bowl, tennis
ball or PVC pipe) beneath soft cover
in the center of griddle in order to
S T E P 1 6 Proceed to the Griddle Seasoning Instructions section of
allow water to slide off. "Tenting"
the Care & Maintenance chapter.
helps prevent rust.
Enjoy cooking outdoors on your Blackstone!
CUT TING ON THE
GRIDDLE TOP
Using a knife directly on the surface
of the griddle will not harm the
griddle top.
REMOVING RUST
If rust appears on the griddle surface,
rub it off with steel wool, low grit
sandpaper or the Blackstone
Pumice Stone and re-season
SOLUTION
the surface.
Replace with new battery.
Recovering your Blackstone
Griddle Top
Ensure that the battery is installed nega-
tive end first.
Ensure that the ignition needle is posi-
tioned 1/8" to 1/4" away from the burner
tube, positioned above a burner hole.
Contact customer service for replace-
ment parts.
youtube.com/
watch?v=thPE2IgnSiI
SOLUTION
Please reference the Gas Flow section of
the Troubleshooting Chapter.
Care & Maintenance Assembly Guide | Owner's Manual
!
WA R N I N G
NEVER APPLY COLD
WATER ACROSS THE
WHOLE SURFACE OF A
HOT GRIDDLE AT ONCE.
This may cause warping.
Adding a large amount
of cold or frozen food (or
food with significant water
Insert one (1) AA battery (not
content) to a hot griddle may
included) into the battery socket
cause griddle to warp.
with the positive terminal facing
out, then screw on the ignitor
!
button until tight. Be careful to not
C A U T I O N
over tighten.
DO NOT USE SOAP ON
THE GRIDDLE COOKING
SURFACE. This will destroy
the griddle's seasoning.
3-7mm
Ensure that the ignition needle is
positioned 3-7mm away from the
burner tube, positioned above a
burner hole.
ASSEMBLY VIDEOS
View Product Assembly and
Technical Support videos online at
blackstoneproducts.com/support
and on YouTube @BlackstoneGriddles
blackstoneproducts.com/support 11