Publicidad
Idiomas disponibles
Idiomas disponibles
Features(Continued)
USING YOURGARAGEDOOROPENER
The garage door opener can be activated through a wall-mounted
door control, remote control, wireless keyless entry or
AssureLink
TM
accessory.
When the door is closed and the garage door opener is activated
the door will open. If the door senses an obstruction or is
interrupted while opening the door will stop. When the door is in
any position other than closed and the garage door opener is
activated the door will close. If the garage door opener senses an
obstruction while closing, the door will reverse. If the obstruction
interrupts the sensor beam the garage door opener lights will
blink 10 times. However, you can close the door if you hold the
button on the door control or keyless entry until the door is fully
closed. The safety reversing sensors do no effect the opening
cycle.
The safety reversing sensor must be connected and aligned
correctly before the garage door opener will move in the down
direction.
Door Control
USINGTHE DOORCONTROL
Push Bar
Navigation
Buttons
LIGHT
Button
Screen
Motion
Sensor
Push Bar
Press the push bar to open or close the door.
Light Button
Press the LIGHT button to turn the garage door opener lights on
or off. When the lights are turned on they will stay on until the
LIGHT button is pressed again, or until the garage door opener is
activated. Oncethe garage door opener is activated the lights will
turn off after the specified period of time (the factory setting is
4-1/2 minutes). The LIGHTbutton will not control the lights when
the door is in motion. The duration of the light timing can be
adjusted using the door control.
Navigation Buttons
Use the navigation buttons to make selections and program
features.
Screen
The screen will display the time and temperature until the menu
button is pressed, and then it will display the menu options. If
there is a problem with the garage door opener the screen will
display the Diagnostic Code. Refer to the Troubleshooting section.
The followingfeatures are accessiblethroughthe screen using
the navigationbuttonson the Smart Control Panel:
LEARNA DEVICE
Any compatible remote controls, wireless keyless entry, or
AssureLink
TM
accessories can be programmed to the garage door
opener by accessing the menu and using the navigation buttons
on the Smart Control Panel.
Lock
The LOCKfeature is designed to prevent activation of the garage
door opener from remote controls while still allowing activation
from the door control and keyless entry. This feature is useful for
added peaceof mind when the home is empty (i.e. vacation).
Timer-to-Close(TTC)
DO NOT enable TTC if operating a one-piece door. TTC is to be
used ONLYwith sectional doors.
Factory default is set to off. TTC can be set to automatically close
your garage door from the fully open position after a specified
period of time (1, 5, 10 minute intervals). The Smart Control Panel
also has a custom setting up to 99 minutes. The garage door
opener will beep and the lights will flash before closing the door.
The screen on the door control will display the status of the TTC
such as time to close, paused, or an error. If the door encounters
an obstruction while closing, the garage door opener will make a
second attempt to close the door. If the obstruction has not been
cleared after the second attempt, the garage door opener will
reverse open, stop and WILL NOTclose until the obstruction has
been cleared. TTCWILL NOTwork if the garage door opener is
operating by battery power or if the safety reversing sensors are
misaligned. This feature is NOT intended to be the primary
method of closing the door. A keyless entry shouldbe installed
in the event of an accidental lock out when usingthis feature.
AUTOMATICLIGHT
Motion Sensor
Factory default is set to on. This feature will automatically turn on
the garage door opener lightswhen motion is sensed.The lights
will come on for the set period of time, then shut off.
The lightswill turn on when someone enters through the open
garage door and the safety reversing sensor infrared beam is
broken.
If using the garage door opener light as a work light disable the
Automatic Light Feature,otherwise the light will turn off
automatically if you are beyond the range of the sensor.
32
Publicidad
