Publicidad
Idiomas disponibles
Idiomas disponibles
Any functional dis orders, especially those affecting the
safety of the machine, sholud terefore be rectified im-
mediately.
• Any other use exceeds authorization. The manufac-
turer is not responsible for any damages resulting from
un authorized use; risk is the sole responsibility of the
operator.
• The safety, work and maintenance instructions of the
manufacturer as well as the technical data given in
the calibrations and dimensions must be adhered to.
• Relevant accident prevention regulations and other,
gene rally recognized safety-technical rules must also
be adhered to.
• The machine may only be used, maintained, and op-
erated by persons familiar with it and instructed in its
operation and procedures. Arbitrary alterations to the
machine release the manufacturer from all responsi-
bility for any resulting damages.
• The machine may only be used with original accesso-
ries and tools made by the manufacturer.
Remaining hazards
The machine has been built using modern technolo-
gy in accor dance with recognized safety rules. Some
remaining hazards, how ever, may still exist.
• Only process selected woods without defects such
as: Branch knots, edge cracks, surface cracks. Wood
with such defects is prone to splintering and can be
hazardous.
• Wood which is not correctly glued can explode when
being processed due to centrifugal force.
• Trim work piece to a rectangular shape, center and
cor rectly secure before processing. Unbalanced work
pieces can be hazardous.
• Long hair and loose clothing can be hazardous when
the work piece is rotating. Wear personal protective
gear such as a hair net and tight fitting work clothes.
• Saw dust and wood chips can be hazardous. Wear
per so nal protective gear such as safety goggles and
a dust mask.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimized by following the
instructions in „Safety Precautions", „Proper Use" and
in the entire operating manual.
• Do not force the machine unnecessarily: excessive
cutt ing pressure may lead to rapid deterioration of the
blade and a decrease in performance in terms of finish
and cutting precision.
• When cutting aluminium and plastics always use the
app ro priate clamps: all workpieces must be clamped
down firmly.
• Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
• Always use the tools recommended in this manual to
obtain the best results from your cutting-off machine.
• Always keep hands away from the work area when
the ma chine is running; before performing tasks of
any kind release the main switch button located on the
handgrip, thus disconnecting the machine.
• Always keep hands away from the work area when
the machine is running; before performing tasks of
any kind release the main switch button located on the
handgrip, thus disconnecting the machine.
Assembly
WARNING! For your own safety, never connect the
plug to power source outlet until all assembly steps
are completed and you have read and understood
the safety and operational instructions.
Lift the saw from the packaging and place it on your work
bench.
Installing the Dust Bag (Fig. 2)
• Squeeze the metal collar wings 2 of the dust bag and
put it on the motor area exhaust port 1.
Setting the Tool
Note:
This tool is accurately adjusted before shipping from the
factory. Check the following accuracy and readjust if nec-
essary in order to obtain the best results in operation.
Installation of the Angle Fence at 90°, Fig. 3
1
Loosen the angle clamping lever (1).
2 Move the cutting head to the right until it rests against
the fence.
3 Tighten the angle clamping lever (1).
4 Test the saw blade with a 90° angle to the saw table.
If an adjustment is necessary, loosen the lock nut (2)
and position the socket screw in such a way that the saw
blade stands at 90° to the table. Re-tighten the lock nut.
5 Set the angle fence (3) with the screw at 0.
Installation of the Angle Fence at 45° Left. Fig.4
1
Loosen the angle clamping lever (1).
2 Move the cutting head to the left until it rests against
the fence.
3 Tighten the angle clamping lever (1).
4 Test the saw blade with a 45° angle to the saw table.
If an adjustment is necessary, loosen the lock nut and
position the socket screw (4) in such a way that the saw
blade stands at 90° to the table. Re-tighten the lock nut.
Installation of the Contact Surface,
• Lower the cutting head and push in the lock pin. Make
sure the table is in 0 mitre position.
• Place a combination square against the fence and
next to the saw blade.
• Loosen the two screws if the saw blade does not
touch the protractor.
• Adjust the fence so that the fence has full contact with
the square. Tighten the screws.
Connecting to the Power Supply
Check that the power supply and outlet used are in ac-
cordance with your mitre saw. Have a look at the rating
plate of the motor or the rating on the mitre saw. Any
changes should always be carried out by a qualified
electrician.
15 І 180
Publicidad
