cecotec BOLERO HEXA AF319000 INOX A Manual De Instrucciones página 27

ENGLISH
with the electrical parts of the oven once it has been installed.
- All parts that ensure the safe operation of the appliance must only be removed with the
aid of a tool.
- To fix the oven to the cabinet, open the oven door and fix it by inserting the 4 wood screws
into the 4 holes on the perimeter of the frame.
Electrical connections
Ovens equipped with a three-pole power cable are designed to operate on alternating current.
The earth wire of the appliance is yellow green.
Mounting the power cable
Fig. 5
Open the terminal board:
- With a screwdriver, tighten the screw on the side tabs of the terminal board cover.
- Unscrew the screws on the side tabs of the cover and remove the latter.
To install the power cable, proceed as follows:
1. Remove the cable clamp screw and the three contact screws.
2. Fix the wires under the screw heads using the following colour scheme: Blue (N) Brown
(L) Yellow Green.
3. Secure the power cable with the cable clamp and close the terminal board cover.
Connecting the power cable to the mains
- Install a standard plug socket corresponding to the load indicated on the rating plate.
When connecting the cable directly to the mains, install an omnipolar circuit breaker with
a minimum contact opening of 3 mm between the appliance and the mains. The omnipolar
circuit breaker must be sized according to the load and comply with the applicable
regulations (the earth cable must not be interrupted by the circuit breaker).
- The power supply cable must be routed so that it does not reach a temperature above 50
˚C above ambient temperature and must be protected by insulation with an appropriate
rating. Before making the connection, check that:
- The electrical safety of this appliance can only be guaranteed if the oven is correctly and
effectively earthed in accordance with electrical safety regulations. Always make sure
that the ground connection is effective; if in doubt, call a qualified technician to check the
system. The manufacturer declines all liability for damage resulting from an ungrounded
system.
- Before connecting the appliance to the mains, check that the specifications indicated on
the rating plate (on the appliance and/or on the packaging) correspond to those of the
mains supply at home.
- Check that the electrical capacity of the installation and the sockets can withstand the
maximum power of the appliance. If in doubt, contact a qualified technician.
52
Bolero Hexa AF319000 Inox A
- If the socket and plug of the appliance are not compatible, ask a qualified technician to
replace the socket with a suitable model. The latter, in particular, will also have to ensure
that the cross-section of the socket cables is adequate for the power used by the appliance.
The use of adapters, multiple sockets and/or extensions is not recommended. If their use
cannot be avoided, remember to use only single or multiple adapters and extension cords
that comply with current safety regulations. In these cases, never exceed the maximum
current capacity indicated on the single adapter or extension cord and the maximum
power indicated on the multiple adapter. The plug and socket shall be easily accessible.
4. OPERATION
Clock setting
- Once the oven is on, the display will show "12:00" and the time icon
- Use the increase/decrease icons to set the current time. Wait 5 seconds for the setting
to be confirmed automatically or press the temperature/time icon
Cooking temperature setting
- Press the temperature/time icon , the corresponding values will flash on the display.
- Press the increase/decrease icons
Automatic time adjustment (fully automatic start and end of cooking time)
1. Press the temperature/time icon
display. Then, use the increase/decrease icons
2. Press the temperature/time icon
display. Next, use the increase/decrease icons
3. Press the temperature/time icon and turn the functions knob to adjust the temperature
and select the cooking mode.
4. After these settings, wait 5 seconds until the
indicating that the selected settings have been successfully confirmed.
For example: if the food needs to be cooked for 45 minutes, the oven is supposed to be turned
off at 14:00.
1. Press the temperature/time icon
display and set the baking time to 45 minutes.
2. Press the temperature/time icon several times until the
and set the cooking end time to 14:00.
3. After these settings, the programmed clock values (hour and minutes) will appear on the
display, indicating that the selected settings have been saved correctly.
4. When the clock strikes 13:15 (between 14 -15 min), the oven will switch on automatically.
5. During the baking time, the corresponding icon will continue to flash.
6. When the clock strikes 14:00, the oven will switch off automatically. The oven will beep
and the corresponding icon will flash. Press any of the icons to stop the sound.
ENGLISH
will flash.
.
to adjust the temperature in 5 °C increments.
several times until the icon flashes on the
to adjust the desired cooking time.
several times until the icon flashes on the
to adjust the switch-off time.
and icons flash on the display,
several times until the icon flashes on the
icon flashes on the display
Bolero Hexa AF319000 Inox A
53