Publicidad
Idiomas disponibles
Idiomas disponibles
9
NOTE: If necessary, refer to the instructions for your device to add or set up
Bluetooth.
When found, your all-in-one system will be displayed as 'SHARP
XL-B720D' on your device. Select this to begin pairing. Once done,
<Connected> will be displayed on your radio.
Paired devices will connect to the all-in-one system when they are within
range (within 10 metres in line of sight). Your device will remain paired
with the radio unless you decide to disconnect it.
To disconnect from Bluetooth, long press
current device and search for new devices.
Wirelessly stream music via Bluetooth
In Bluetooth mode, you can wirelessly stream audio through the all-in-
one system. Use the controls on your paired Bluetooth device as well as
those on your all-in-one system. Controls available:
Short press to Play/Pause.
Short press to move to previous track. Long press to rewind within
a track.
Short press to move to next track. Long press to forward within a
track.
Press to stop.
Volume can also be adjusted – either using your all-in-one system and/or
your connected device.
NOTE: If the all-in-one system is inactive for 20 minutes, or no audio signal is
being received, the all-in-one system will automatically go into standby.
Rewind and fast forward functions in Bluetooth are dependant on the
software playing the audio.
USB mode
Ensure your all-in-one system is in USB mode by short pressing
until the all-in-one system displays <USB>.
Insert the USB stick which has the MP3 files you wish to play into the
USB input.
NOTE: If the USB does not insert easily, try rotating it by 180 degrees and try
again. Never force the USB stick into the socket or try to insert it at an angle
as this could damage the socket.
NOTE: USB drives up to 64GB FAT32 are supported.
The following controls are available when using a
USB:
Short press to Play/Pause.
Short press to move to previous track. Long press to rewind within
a track.
Short press to move to next track. Long press to forward within a
track.
Press to stop.
NOTE: To navigate the folders on the USB, use
control.
Programmed play
Using your remote control, you can program the play order of up to 99
tracks on your USB stick.
NOTE: To set up programmed play, the USB stick file must not be paused or
playing.
While in USB mode:
In USB mode, with the files you wish to programme on the USB inserted
into the unit and not playing or paused.
to enter USB programmed play mode <T001 P01> will be
Press
displayed.
Use
or
to go to the track number that you would like to program
to play first. Press
to confirm.
You will now be able to select the second track that you would like to
for 3 seconds to unpair your
and
on the remote
program. Continue to select each track as above, up to a total of 99
tracks.
Press
to play the programmed tracks.
To exit programmed play mode, press .
Aux in mode
To change to an Aux-input, short press
displays <Aux in>.
Use a 3.5mm audio input connection cable (not included) for a quick and
easy connection to an external audio source.
Connect one end of the 3.5mm audio connection cable to the
headphone (or auxiliary out) socket of your secondary device, connect
the other end to the Aux in socket on the rear of your all-in-one system.
Press the Play button on your external device to start playback through
the all-in-one system speakers.
To gain optimal volume levels, adjust the output volume level on both
the secondary device and on the all-in-one system.
NOTE: It is recommended that you unplug the Audio cable from the Aux in
socket after you have finished listening to your external device.
Alarm functionality
Set an alarm
NOTE: Check that the all-in-one system is displaying the correct time and
date before you set an alarm.
Full Scan
Manual Tune
DAB+
DRC
Prune
System
Scan setting
Audio setting
FM
AMS
System
BT
System
Alarm
Alarm 1 Setup
Alarm 2 Setup
Time
Duration
Source
Frequency
Volume level
Alarm
NOTE: If the time is not set or has failed to update from the radio signal,
<Time is not set> will be displayed when you try to set the alarm. The all-
in-one system will then prompt you to set the time. An alarm can only be set
after the time has been set.
until the all-in-one system
System
Sleep
Alarm
Equaliser
Time
Backlight
Language
Factory reset
Software Version
Alarm 1 or 2 settings
Hour
Min
1, 5, 10, 15, 30, or 60 minutes
Buzzer, DAB, or FM
Daily, once, weekdays or weekends
25%-100%
On or Off
Publicidad
