DSC HS2016 Manual De Usuario página 46

1 2 R e g u l a t o r y A g e n c y S t a t e m e n t s
INDUSTRY CANADA STATEMENT
NOTICE: The models: HS2128, HS2064, HS2032, HS2016 meet the appli-
cable Industry Canada Terminal Equipment Technical Specifications. This
is confirmed by the registration number. The abbreviation, IC, before the
registration number signifies that registration was performed based on a Dec-
laration of Conformity indicating that Industry Canada technical specifica-
tions were met. It does not imply that Industry Canada approved the
equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equip-
ment is 0.1. The REN assigned to each terminal equipment provides an indi-
cation of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any com-
bination of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all devices does not exceed 5.
HS2016 Registration number IC:160A-HS2128
HS2032 Registration number IC:160A-HS2128
HS2064 Registration number IC:160A-HS2128
HS2128 Registration number IC:160A-HS2128
This product is in conformity with EMC Directive 2004/108/EC based on re-
sults using harmonized standards in accordance with article 10(5), R&TTE
Directive 1999/5/EC based on following Annex III of the directive and LVD
Directive 2006/95/EC based on results using harmonized standards.
This product meets the requirements of Class II, Grade 2 equipment as per
EN 50131-1:2006 + A1:2009 Standard. This product is suitable for use in
systems with the following notification options:
- A (use of two warning devices and internal dialer required),
- B (self powered warning device and internal dialer required),
- C (internal dialer and alternate IP/3G communicator required)
- D (use of alternate IP/GSM communicator with encryption enabled re-
quired).
The Model HS2016, HS2032, HS2064, HS2128
Control Panel has been certified by Telefication according to EN50131-
1:2006 + A1:2009, EN50131-3:2009, EN50131-6:2008 and EN50136-
1:1997 for Grade 2, Class II, ATS2.
FCC AND INDUSTRY CANADA STATEMENTS FOR WIRELESS
KEYPADS
Models: HS2LCDRF9, HS2LCDRFP9, HS2ICNRF9, HS2ICNRFP9 (oper-
ating in 912-919MHz band) are compliant with applicable FCC Part 15.247
and IC RSS-210 rules.
WARNING! To comply with FCC and IC RF exposure compliance require-
ments, the HS2LCDRF(P)9 or HS2ICNRF(P)9 keypads should be located at
a distance of at least 20 cm from all persons during
normal operation. The antennas used for this product must not be co-located
or operated in conjunction with any other antenna or transmitter.
This device complies with FCC Rules Part 15 and with Industry Canada li-
cense-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2)this
device must accept any interference that may be received or that may cause
undesired operation.
IC:160A – HS2KRFP9
The term "IC" before the radio certification number only signifies that Indus-
try Canada technical specifications were met.
AVERTISSEMENT! Pour répondre aux exigences de conformité de la
FCC et d'Industrie Canada sur les limites d'exposition aux radiofréquences
(RF), les pavés numériques HS2LCDRF(P)9 ou HS2ICNRF(P)9 doivent
être installés à une distance minimale de 20 cm de toute personne lors de leur
fonctionnement usuel. Ces derniers ne doivent pas être situés au même en-
droit, ni être en fonction avec une autre antenne ou un autre transmetteur.
Le present appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisee aux deux
conditions suivantes:
(1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioelectrique subi, meme si le brouillage est
susceptible d'en compromettre le fonctionnement.
Le present appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisee aux deux
conditions suivantes:
(1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioelectrique subi, meme si le brouillage est
susceptible d'en compromettre le fonctionnement.
The following is a list of warnings applicable when this equipment is con-
nected to the New Zealand Telecom Network.
GENERAL WARNING
The grant of a Telepermit for any item of terminal equipment indicates only
that Telecom has accepted that the item complies with minimum conditions
for connection to its network. It indicates no endorsement of the product by
Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model, nor does it imply
that any product is compatible with all of Telecom's network services.
REVERSE NUMBERING (DECADIC SIGNALLING)
Decadic signaling should not be used as it is being progressively phased out
of the network. DTMF dialling is 100% available and it should always be
used.
LINE GRABBING EQUIPMENT
This equipment is set up to carry out test calls at pre-determined times. Such
test calls will interrupt any other calls that may be set up on the line at the
same time. The timing set for such test calls should be discussed with the in-
staller. The timing set for test calls from this equipment may be subject to
'drift'. If this proves to be inconvenient and your calls are interrupted, then
the problem of timing should be discussed with the equipment installer. The
matter should NOT be reported as a fault to Telecom Faults Service.
D.C. LINE FEED TO OTHER DEVICES
During dialing, this device unit does not provide DC voltage to the series port
connection and this may cause loss of memory functions for the terminal de-
vices (local telephone) connected to T-1, R-1.
General operation (ringer sensitivity and loading)
This device only responds to Distinctive Alert cadences DA1 and DA2.
In the event of any problem with this device, it is to be disconnected. A CPE
item connected to one of the device's terminal ports may be connected di-
rectly in its place. The user should then arrange for the product to be repaired.
Should the matter be reported to Telecom as a wiring fault, and the fault is
proven to be due to this product, a call-out charge will be incurred.
46