Craftsman 351.215690 Manual Del Usuario página 6

The power lines are inserted directly onto the switch. The
green ground line must remain securely fastened to the frame
to properly protect against electrical shock. The power supply
to the motor is controlled by a single pole locking rocker switch.
• Remove the key to prevent unauthorized use.
Refer to Figures 10 - 19.
DESCRIPTION
The Craftsman Belt and Disc Sanders are constructed of
rugged die cast aluminum and cast iron providing stability and
vibration-free operation. The belt and disc are used to sand,
deburr, bevel and grind large workpieces of wood and plastic.
The belt housing can be pivoted from vertical to
horizontal for sanding large, straight workpieces. The idler
drum permits the sanding of contoured shapes and finishes.
The disc can be used to sand or bevel surfaces.
Built-indust collection system collects dust from the belt and
disc, and exhausts the dust into an included 30-micron
collection bag.
The adjustable miter gauge can be used on both the belt and
disc tables for guiding the workpieca at a desired angle while
sanding. Work stop included for sanding long pieces on the
belt.
SPECIFICATIONS
MODEL 215690
Belt size .................................... 4 x 36"
Belt platen area ............................... 5 x 9"
Belt speed ................................ 1900 FPM
Disc diameter .................................... 8"
Disc speed ............................... 3000 RPM
Table dimensions .............................. 6 x 9"
Table tilts ................................... 0 to 45"
Dust port diameter ................................ 2"
Base dimensions ............................ 12 x 17"
Switch ............................. SR Locking rocker
Weight ...................................... 77 Ibs
MODEL 225930
Belt size .................................... 6 x 48"
Belt platen area .............................. 7 x 17"
Belt speed ................................ 2700 FPM
Disc diameter .................................... 9"
Disc speed ............................... 3500 RPM
Table dimensions ............................. 7 x 10"
Table tilts................................... 0 to 45°
Dust port diameter ................................ 2"
Base dimensions........................... 15% x 20"
Switch ............................. SP, Locking rocker
Weight ..................................... 110 Ibs
WARNING: Operation of any power tool can result in foreign
objects being thrown into the eyes, which can result in severe
eye damage. Always wear safety goggles complying with
United States ANSI Z87.1 (shown on package) before com-
mencing power tool operation. Safety goggles are available at
Sears retail stores or catalog.
CAUTION: Always observe following safety precautions.
SAFETY PRECAUTIONS
• Whenever adjusting or replacing any parts on the tool, turn
switch OFF and remove the plug from power source.
• Recheck table knob and bolts. They must be tightened
securely.
• Make sure all guards are properly attached. All guards
should be securely fastened.
• Make sure all moving parts are free and clear of any
interference,
• Make sure all fasteners are tight and have not vibrated loose.
• With power disconnected, test operation by hand for clear-
ance and adjust if necessary.
• Always wear eye protection or face shield.
• Make sure abrasive belt always tracks properly. Correct
tracking gives optimum performance.
• After turning switch on, always allow belt and disc to come
up to full speed before sanding or grinding.
• Be sure disc turns counterclockwise. Abrasive belt must
travel downward.
• Avoid kickback by sanding in accordance with the direction-
al arrows.
• Keep your hands clear of abrasive belt, disc and all moving
parts.
• For optimum performance, do not stall motor or reduce
speed. Do not force the work into the abrasive.
• Always support workpiece with table or work stop when
sanding with belt and with table when sanding with disc.
• Never push a sharp corner of the workpiece rapidlyagainst
the belt or disc. Abrasive backing may tear.
• Replace abrasives when they become loaded (glazed) or
frayed.
ON/OFF SWITCH
Refer to Figure 10, page 7.
The ON/OFF switch is located on the upper front right of the
cabinet. To turn the sander ON, pull the switch to the up
position.To turn the sander OFF, push the switch to the down
position.
The sander can be locked from unauthorized use by locking
the switch. To lock the switch:
• Turn the switch to OFF position and disconnect sander
from power source.
• Pull the key out. The switch cannot be turned on with the
key removed.
NOTE: Should the key be removed from the switch at the ON
position, the switch can be turned off but cannot be turned on
again.
• To replace key, slide key into the slot on switch until it snaps.