EINHELL GC-EM 1600/37 Manual De Instrucciones Original página 21

The cutting height is adjusted as follows
(see Fig. 9):
1. Push the lever inwards.
2. Set the lever to the desired cutting height.
3. Release the lever and check that it is securely
seated in the lock.
Reading off the cutting height
The cutting height can be set between 20-60 mm
in 5 intervals, and can be read off on the scale.
Power supply
The lawn mower can be connected to any light
socket-outlet with a 220-240 Volt alternating
current. However, the socket outlet must have an
earthing contact protected by a 16 A circuit brea-
ker. Additionally, a residual current device (RCD)
circuit-breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not dama-
ged. The total length of the power cable should
not exceed 50 meters; going beyond this distance
will reduce the power output of the electric motor.
The power cable must have a cross-section of
3 x 1.5 mm². The insulating sheath of lawn aerator
power cables is frequently damaged.
Some of the causes for this are:
•
Cuts caused by driving over the cable.
•
Pinching when the power cable is dragged
under doors and pulled through windows.
•
Cracking due to old age of the insulation.
•
Kinking by improperly fastening or guiding the
power cable.
The power cables must, at the very minimum, be
of type HO5RN-F and 3-stranded. The cable type
must be printed somewhere on the power cable.
Only purchase power cables that are marked!
Plugs and socket couplers for the power cables
must be made from rubber and splash-proof.
There is a limit to how long power cables can be.
Longer power cables require larger conductor
cross-sections. Power cables and connecting li-
nes must be regularly checked for damage. Ensu-
re that the lines are switched off before checking
them. Completely unwind the power cable. Also
check power cable entry points, plugs and socket
couplers for kinks.
Anl_GC_EM_1600_37_SPK13.indb 21 Anl_GC_EM_1600_37_SPK13.indb 21
GB
6. Operation
Connect the plug (Fig. 1/Item 8) to an extension
cable. It is imperative to secure the extension
cable with the cable grip as shown in Fig. 10.
Caution!
To prevent the machine switching on accidentally,
the lawn mower is equipped with a safety lock-off
(Fig. 10/Item A) which must be pressed before the
switching bar (Fig. 10/Item B) can be activated.
The lawn mower switches itself off when the swit-
ching bar is released. Repeat this process several
times so that you are sure that the machine func-
tions properly. Before you perform any repair or
maintenance work on the equipment, ensure that
the blade is not rotating and that the power supply
is disconnected.
Caution! Never open the chute fl ap when the
grass bag has been detached (to be emptied)
and the motor is still running. A rotating bla-
de can cause serious injuries!
Always carefully fasten the chute fl ap and grass
basket. Switch off the engine before emptying the
grass basket.
Always ensure that a safe distance (provided
by the length of the long handles) is maintained
between the user and the mower housing. Be
especially careful when mowing and changing
direction on slopes and inclines. Maintain a solid
footing and wear sturdy, non-slip footwear and
long trousers.
Always mow along the incline (not up and down).
For safety reasons, the lawn mower may not be
used to mow inclines whose gradient exceeds 15
degrees.
Use special caution when backing up and pulling
the lawn mower. Tripping hazard!
Tips for proper mowing
It is recommended that you overlap the mowing
swaths.
Only use a sharp blade that is in good condition.
This will prevent the grass blades from fraying
and the lawn from turning yellow.
Try to mow in straight lines for a nice, clean look.
The swaths should overlap each other by a few
centimeters in order to avoid stripes.
- 21 -
09.05.2023 15:04:53 09.05.2023 15:04:53