Publicidad
Idiomas disponibles
Idiomas disponibles
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. R)
1. Attach the dust extraction adaptor
the Dust Extraction Adaptor.
2. Attach the sanding platen
Installing/Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust Extraction Adaptor.
2. Push dust extraction arm
19
dust extraction adaptor
17
3. Attach plunge cutting blade as described under Installing/
Removing Accessories.
4. Adjust the dust extraction arm
Helpful Hints
•
Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
•
Do not start sanding without having the sandpaper
attached to sanding platen.
•
Use coarse grit paper to sand rough surfaces, medium grit
for smooth surfaces and fine grit for the finishing surfaces. If
necessary, first make a test run on scrap material.
•
Excessive force will reduce the working efficiency and cause
motor overload. Replacing the accessory regularly will
maintain optimum working efficiency.
•
Do not allow the sandpaper to wear away, it will damage
the sanding pad.
•
If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for 2–3
minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
17
. Refer to Attaching
as described under
23
into the lower aperture of the
.
19
for best results.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Compatible accessories
Oscillating sanding pad
Oscillating wood w/ nails blade
Wide titanium oscillating wood w/ nails blade
Oscillating hardwood blade
Oscillating fastcut wood blade
Wide oscillating fastcut wood blade
Oscillating wood detail blade
Oscillating titanium metal blade
Oscillating semicircle blade
Oscillating titanium semicircle blade
Oscillating flush cut blade
Titanium oscillating flush cut blade
Oscillating multi-material blade
Oscillating rigid scraper blade
Oscillating flexible scraper blade
Oscillating carbide grout removal blade
Oscillating fastcut carbide grout removal blade
Oscillating carbide rasp
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
EngLIsh
WALT recommended
e
37
Publicidad
