Safety Instructions - Walter Surface Technologies SURFOX 205 Manual De Usario

Safety Instructions

WALTER weld cleaning machines are produced in accordance
with applicable standards governing the manufacture,
performance and safety of industrial products.
WARNING!
When using these machines, basic
safety precautions should always be observed to
reduce the risk of fire, electrical shocks and personal
injuries.
Before using this machine, read all Safety and Operating
Instructions carefully and save this owner's manual for
future reference.
1. Read this owner's manual to familiarize yourself with
this unit's operation, its particular features, applications
and limitations.
2. This unit is equipped with a 3-conductor power cord
and 3-prong electrical plug, it must be connected to a
correspondingly grounded receptacle.
Allow a minimum of 8" clearance around the unit to
3.
keep all air openings clear of any obstruction. Free
airflow through the vent openings is required to
prevent the unit from overheating.
4. Keep work area clean and well lit. A cluttered environment
invites accidents. Remove any material that may be
ignited by sparks. Do not use this tool when flammable
liquids or gases are present. Keep handles clean, dry
and free from cleaning solution, oil and grease. Do not
use in rain, damp or wet locations.
5. Keep children and other persons at a safe distance
from the work. Make sure no one is under you when
working in high places. Do not let unqualified persons
handle this machine.
When working, always wear appropriate clothing and
6.
safety gear, such as suitable and safety approved
chemical resistant gloves, overalls, safety shoes, etc.
Always wear approved safety goggles.
7.
8. During the cleaning process, the wand tip and work
piece can reach very high temperatures, allow to cool
before coming in contact with exposed skin.
9. Avoid inhalation of fumes, use only in well ventilated
areas. Use a respirator, if necessary.
10. All electric shocks can be potentially dangerous.
11. Should you encounter an electrical problem, do not
use the unit until qualified personnel have inspected
the equipment.
12. Never operate the unit with its protective cover removed.
13. Stay alert at all times when handling this unit. Watch
what you are doing. Use common sense. Do not
operate the tool when you are tired. Never leave it
running unattended.
14. Make sure the switch is in its OFF position before
plugging in or when moving the unit to avoid
unintentional starting.
15. Hold the wand firmly. Do not overreach, maintain
good footing and balance at all times.
16. Before use, all parts should be carefully examined to
determine that the unit will operate properly and
perform its intended function.
17. Parts that are damaged or defective should be
properly repaired or replaced by a WALTER Factory
Service Center or a WALTER Authorized Service Center.
18. Do not use the unit if the switch does not turn ON and OFF.
19. Use only the accessories recommended for this
system. Always check accessories before starting to
work and do not use if damaged.
20. CAUTION: WALTER SURFOX electrolyte weld
cleaning solutions contain phosphoric acid and may
cause burns when not handled properly. Avoid skin contact.
First aid Wash affected area with water.
Eye contact Flush with water for 15 minutes lifting
eyelids occasionally. Contact physician if necessary.
Ingestion DO NOT induce vomiting. Rinse mouth,
drink plenty of water and get medical attention.
Refer to WALTER product MSDS for complete safety
data information.
21. Use only WALTER SURFOX electrolyte weld cleaning
solutions with this unit and NEVER mix it with any
other products.
22. Store solution in its original container and in a safe
place, out of the reach of children and other unqualified
persons. Keep container contents clean. Do not reuse
SURFOX electrolyte cleaning solutions.
23. Do not touch the wand tip or work piece while
working or immediately after use, they may be
extremely hot and could cause serious burns.
24. Do not abuse the power cord. Never pull or lift this
unit by its cord or yank to disconnect it from the
receptacle. Keep the cord away from heat, oil and
sharp edges. Inspect the cord periodically, if damaged,
have it replaced by a WALTER Factory Service
Center or a WALTER Authorized Service Center.
25. When not in use, switch OFF and unplug the electrical
cord and air hose (if connected). It must also remain
unplugged when replacing cleaning pads and other
accessories, while performing maintenance and
before servicing.
26. Store the unit in a dry safe place, out of the reach of
children and other unqualified persons.
2
Safety Instructions
3
SURFOX 205 User's Guide