Baxi LUNA DUO-TEC MP 1.90 Manual De Uso página 33

(a) (b)
ZONE 1 HEATING PARAMETERS
P01 700 *Operating mode (0=Antifreeze, 1=Timed, 3=T.comfort)
P02 712 *Reduced ambient temperature
P03 720 *"Kt" curve slope
P04 721 *"Kt" curve drift
P05 726 *"Kt" curve adaptation
P06 741 Flow temperature setpoint (maximum value)
P07 742 *Enable modulating temperature if set = "---"
P08 750 *Ambient influence
P09 834 *Opening/Closing speed of mix valve
ZONE2 HEATING PARAMETERS
P10 1000 *Operating mode (0=Antifreeze, 1=Timed, 3=T.comfort)
P11 1010 *Comfort room temperature
P12 1012 *Reduced ambient temperature
P13 1020 *"Kt" curve slope
P14 1021 *"Kt" curve drift
P15 1026 *"Kt" curve adaptation
P16 1041 Flow temperature setpoint (maximum value)
P17 1042 *Enable modulating temperature if set = "---"
P18 1050 *Ambient influence
P19 1134 *Opening/Closing speed of mix valve
DHW PARAMETERS
Operating mode in DHW (with Remote Control)
P20 1620 0=always enabled, 1=according to hourly heating programme,
2= according to hourly DHW programme.
Anti-legionellosis function Disabled/Periodic (boiler with storage unit)
P21 1640
0=disabled, 1=periodic (depending on P22), 2=once a week
Periodic anti-legionellosis function enable (only if P21 =1)
P22 1641
1=daily, 2..6=intervals of 2..6 days, 7=once a week
P23 1663 Circulation temperature setpoint (additional DHW pump)
P24 5470 Preheating time for DHW circuit (1=10' -- 144=1440')
BOILER PARAMETERS
P25 2243 Minimum boiler off time
P26 2217 Anti-freeze setpoint
P27 2250 Pump post-circulation time
P28 2441 Max. fan speed (heating)
P29 2455 Minimum boiler off differential
SOLAR PLANT PARAMETERS (with accessory Expansion Unit)
P30 3810 Temperature - on differential
P31 3811 Temperature - off differential
P32 3850 Solar panel manifold overheating protection ("---" = disabled)
P33 5051 Maximum temperature of storage boiler
CONFIGURATION
P34 5700 Not used (Do NOT change this parameter)
P35 5710 Zone 1 heating circuit (1=enabled)
P36 5715
Zone 2 heating circuit (1=enabled)
P37 5890 Not used (Do NOT change this parameter)
P38 5931 *BX2 sensor input (first auxiliary sensor – section 11)
P39 5932 *BX3 sensor input (second auxiliary sensor – section 11)
P40 5977 *Input H5 (multifunction input – 18=Room thermostat)
P41 6020 *Configuration of accessory Expansion Unit
P42 6220
Software version
MAINTENANCE
P43 7045
Time after maintenance
P44 6704 View/Hide secondary fault internal code
BURNER CONTROL
P45 9512 Required ignition speed
P46 9524 Required minimum operating speed
P47 9529 Required maximum operating speed (high speed)
BOILER CONTROL PANEL PARAMETERS
P48 3 Unit of measurement (1=bar, °C – 2=PSI, °F)
P49 4 Control panel operation: (1=central, 0=local)
P50 5 Software version
* see "Accessories not included in supply"
xx: the value depends on the software version
(a): parameters read on the front boiler panel (fixed control panel)
(main zone)
(with accessory Expansion Unit)
(low speed)
xxx : the value depends on the type of boiler
(b): parameters read on the Remote Control
33
Factory
Minimum Maximum
setting
3 0
°C 16 4
1,5 0,1
- 0 - 4,5
- 1 0
°C 80 20
°C 80 20
50
% 1
s 180 30
°C 3 0
20 4
°C 16 4
- 1,5 0,1
- 0 - 4,5
- 1 0
°C 80 20
°C 80 20
% 50 1
s 180 30
- 0 0
- 0 0
- 7 1
°C 45 8
min 0 0
min 3 0
°C 5 -20
min 3 0
rpm xxx 0
°C 10 0
°C 8 0
°C 4 0
°C --- 30
°C 90 8
- ---
- 1 0
0
- 0
- 33 0
0
- 0
- 0 0
18
- 0
- 0 0
---
- 0
xxx
0
1 0
rpm xxx 0
rpm xxx 0
rpm xxx 0
- 1 1
- 1 0
xx 0
7104645.02 (1-01/12)
3
35
4
4,5
1
80
80
100
873
3
35
35
4
4,5
1
80
80
100
873
2
2
7
80
144
255
20
20
8000
20
40
40
350
90
1
1
43
19
19
32
7
99
240
1
8000
8000
8000
2
1
999