Emerson AVENTICS Sentronic 625 Instrucciones De Montaje página 18

PP
Pressure range
03 3 bar 32
04 4 bar 33
05 5 bar 34
06 6 bar 35
07 7 bar 36
08 8 bar 37
09 9 bar 38
10 10 bar 39
11 11 bar 40
12 12 bar 41
13 13 bar 42
14 14 bar 43
15 15 bar 44
1)
16 16 bar 45
1)
17 17 bar 46
1)
18 18 bar 47
1)
19 19 bar 48
1)
20 20 bar 49
3)
21 21 bar 50
3)
22 22 bar V1
3)
23 23 bar V2
3)
24 24 bar V3
25 25 bar 3) P1
3)
26 26 bar P2
3)
27 27 bar P3
3)
28 28 bar P4
3)
29 29 bar P5
Notes
1)
Only for size: 0, 1, 2, 3, 5, 6, 7, D, E, F, G, J, K, L
2)
Only for size: 8, M
3)
Only for size: 7, 8, L, M
Other versions on request.
5.3 Product overview
5.3.1 Operating elements
6
5
3
4
1
Fig. 1: Operating elements overview
1 Pressure supply input connection
3 Exhaust
5 Proportional solenoid
7 Communication interface, sealing
cap with pressure compensation
membrane
9 2 buttons
AVENTICS™ Sentronic 625 | IM502079-014-R01 | English
2)
32 bar M1 100 mbar
2)
33 bar M2 200 mbar
2)
34 bar M3 300 mbar
2)
35 bar M4 400 mbar
2)
36 bar M5 500 mbar
2)
37 bar M6 600 mbar
2)
38 bar M7 700 mbar
2)
39 bar M8 800 mbar
2)
40 bar M9 900 mbar
2)
41 bar A1 0 ... 1 bar abs.
2)
42 bar A2 0 ... 2 bar abs.
2)
43 bar A3 0 ... 3 bar abs.
2)
44 bar A4 0 ... 4 bar abs.
2)
45 bar A5 0 ... 5 bar abs.
2)
46 bar A6 0 ... 6 bar abs.
2)
47 bar A7 0 ... 7 bar abs.
2)
48 bar A8 0 ... 8 bar abs.
2)
49 bar A9 0 ... 9 bar abs.
2)
50 bar B1 0 ... 10 bar abs.
shutoff version
Vacuum B2 0 ... 12 bar abs.
bypass version
Vacuum B3 0 ... 16 bar abs.
shutoff version
Vacuum B4 0 ... 20 bar abs.
0 ... 50 psi. B5 0 ... 50 bar abs.
0 ... 100 psi. B6 0 ... 100 bar abs.
0 ... 150 psi. B7 0 ... 500 bar abs.
0 ... 200 psi. XX No internal sensor
1)
0 ... 250 psi. VV No internal sensor /
vacuum
10
9
2 Output connection
4 Through hole for mounting
6 Electrical supply
8 Connection for ground, M4
10 LC display
6 Assembly and installation
Before you start with the installation: Familiarize yourself with the basic specifica-
tions for assembly as early as possible in advance. See
g 6.3 Preparation.
6.1 Notes on safety
Danger of injury due to leaks
Leaks lead to uncontrolled escape of compressed air and can cause severe in-
juries.
Only use connection seals that are not made of teflon or hemp.
u
6.2 Planning
6.2.1 Installation conditions
General requirements
• Take the product into account when equalizing potentials in the system.
• Make sure that the product is installed in a manner that protects it from all
types of mechanical loads.
1) Product-specific requirements
1)
• Mounting orientation. See
5)
• Compressed air specifications. See
• Recommendation: Use oil-free compressed air.
• When using oiled compressed air (not recommended):
– Maximum oil content. See
– Only use oils approved for AVENTICS products.
– Make sure that the oil content remains constant during the entire service
life of the product.
– Never change from oiled to oil-free compressed air.
• Only operate the product with a voltage source and control voltage suitable
for PELV. The voltage source must ensure secure electrical isolation of the op-
erating voltage from the mains in accordance with IEC / EN 60204-1 (accident
prevention).
• Never ground the 24 V side of the supply voltage.
• The product causes high-frequency interference. Take appropriate interfer-
ence suppression measures if there are any sensitive devices in the vicinity
and the product is used in environments in accordance with IEC 61000-2-4.
Ambient conditions
• Let the product acclimatize for a few hours before installation. Otherwise wa-
ter may condense in the housing.
• Keep the installation location free from vibration.
• Protect the product from direct sunlight and UV radiation.
7
• Make sure that there are no ferromagnetic sources near the product.
8
• Make sure that the exchange of ambient air is guaranteed to prevent the
product from overheating.
2
• Avoid increased output pressure tolerances: Make sure that high-frequency
radiation from interference-emitting devices is kept away from the product.
4
• If the product is installed near heat sources: Shield the product.
• Ensure that the shielding does not enclose the product.
6.2.2 Required accessories, materials and tools
Select material and tools that are suitable for your product configuration. De-
pending on the configuration, you will need further accessories.
Mounting material
Assembly requires the following material, which is not included in the scope of
delivery. Respect dimensions and tightening torques.
• 2x screws
• 2x seals
• 1x silencer
• 1x screw for ground
• 2x tooth lock washer for ground
g 6.2 Planning
WARNING
g 14. Technical data.
g 14. Technical data.
g 14. Technical data.
and
18