Ryobi EMS216 Manual Del Usuario página 7

●
Check that the operation of the blade guards are not
restricted by the position of the work piece.
●
Ensure that the fence and other parts of the product
will not be cut as the blade lowers to the cutting
position.
■
Start the motor and allow the blade to reach full speed
before slowly lowering it to cut the work piece. Slide
the blade assembly backwards and/or forwards to
complete the cut as necessary.
■
Allow the blade assembly to rise to its upper position
where the blade guards are fully closed. Switch off the
motor and allow the blade to come to a complete stop
before removing the work piece or off-cuts, or before
reaching into the area of the blade.
Before fi rst use, ensure that the angle of the bevel or mitre
set on the product matches the angle to be produced on
the work piece. Check this on a discarded piece of wood by
using a carpenter's set or mitre square.
WARNING
The manufacturer strongly recommends that the product
is always securely mounted to a bench top.
When the base of the product is fi rmly secured to a bench
top by four nuts, bolts and washers as instructed, the
product can be used at maximum bevel and mitre setting
without the possibility of it tipping over. If the product is not
secured properly, the product may over balance when large
bevel angles are selected.
At the front of the mitre saw base there is an extending bar
which should be pulled out to its furthest extent. This will
help prevent the mitre saw from over balancing.
There is also an adjustable screw (balancing foot) that
extends from the bottom of the extension turntable. This
screw should be adjusted so that it touches the fl at surface
that the product is resting upon. This will also prevent the
product from over balancing when cutting at the full extent
of the slide and bevel. Beware, this part of the saw table
moves when diff erent mitre angles are selected, so the
screw needs to be frequently adjusted and reset.
MAINTENANCE
■
Do not modify the product in any way or use accessories
not approved by the manufacturer. Your safety and that
of others may be compromised.
■
Do not use the product if any switches, guards or
other functions does not work as intended. Return to
an authorised service centre for professional repair or
adjustment.
■
Do not make any adjustments whilst the saw blade is
in motion.
■
Always make sure the power plug has been
removed from the mains power source before
making adjustments, lubricating or when doing any
maintenance on the product.
■
Before and after each use, check the product for
damage or broken parts. Keep the product in top
working condition by immediately replacing parts with
spares approved by the manufacturer.
■
The blade has sharp edges and may also remain hot
after cutting operations. Exercise extreme caution when
cleaning an exposed blade. Wear gloves to protect
yourself from personal injury.
■
Clean the saw and its accessories from dust regularly,
especially moving parts including the blade guard.
Use a hand brush or vacuum cleaner to remove dust
effectively. Do not use compressed air.
■
To assure safety and reliability, all repairs, including
changing brushes, should be performed by an
authorised service centre.
■
If the power cord is damaged, it must be replaced by
an authorised service center in order to avoid a hazard.
WARNING
Do not attempt to disassemble the blade guard assembly
for cleaning or repair. Damaged guards should not be
used. Return to an authorised service centre for repair
or replacement.
WARNING
For greater safety and reliability, all repairs should be
performed by an authorised service centre.
Maximum cutting depth stop
The maximum cutting depth stop is to prevent the saw
blade from cutting into the metal base of the unit.
WARNING
The maximum cutting depth stop is not user adjustable.
Do not adjust the maximum cutting depth stop.
TRANSPORTATION AND STORAGE
■
When storing the product, disconnect the power
cord. Store the product in a secure place that is not
accessible to children. Store the power cord as shown
in the illustration on page 205 - 206 of this manual.
■
Clean the product using a brush and vacuum cleaner
before storage.
■
If you remove the saw blade or keep spares with
the unit, ensure they are in the original packaging to
prevent injury.
To secure the product prior to movement:
■
The product should be stored at the zero degree mitre
and bevel angle and locked in position. The slide should
be locked. The handle should be locked in the lower
(safe) position with the guards closed.
■
One or both sides of the work piece supports can be
removed for ease of carrying.
To move or transport in a vehicle:
■
Secure the product prior to movement as described in
the manual.
■
Remove the product from the bench top by releasing
the 4 bolts, one at each corner. Secure the bolts for
future use. Lift the product using the handle at the top.
■
When lifting to a height, two persons wearing heavy
gloves are needed to lift the base of the product.
■
When transporting in a vehicle, set the product on its
base and secure against movement.
5
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL