Publicidad
Idiomas disponibles
Idiomas disponibles
EN
3. USE GUIDELINES
The device is designed to heat air on balconies, terraces
and gardens.
The product is not intended for indoor use!
The product is intended for home use only!
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
1
2
3
4
5
6
1.
Heating element
2.
Knob
3.
Pull switch
4.
Center post
5.
Power cord
6.
Base
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. There should be at least 10 cm distance
between each side of the device and the wall or other
objects. The device should always be used when positioned
on an even, stable, clean, fireproof and dry surface, and
be out of the reach of children and persons with limited
mental and sensory functions. Position the device such that
you always have access to the power plug. The power cord
connected to the appliance must be properly grounded
and correspond to the technical details on the product
label.
CAUTION! The device is equipped with an anti-
tilt switch that turns the device off in the event
of its overturning and turns it on automatically
when restored to a vertical position.
10
CAUTION! Never turn the heating part of the
device during operation. To change the angle
of inclination of the heating section, wait 15
minutes after switching the device off.
ASSEMBLING THE DEVICE
1.
Remove the screws from the base (8 pieces
M6x30).
2.
Remove the lid of the base.
3.
Fix the lower part of the base to the ground with 3
expansion bolts (M4x50).
4.
Put the lid on and screw it to the bottom of the
base with 4 screws (M6 * 30).
5.
Insert the lower part of the post into the hole in
the base and fix it with 4 screws (M6x30).
6.
Slide the screw cover (1) all the way down.
7.
Connect the center and bottom of the post with 3
screws (M5x6).
8.
Connect the top and center of the post with 3
screws (M5x6).
9.
Attach the heating element to the top of the post
and tighten the knob tightly. Put the power cord
into the special holders on the post.
10.
Set the angle of inclination of the heating element
according to your preferences (0° – 45°).
11
EN
11.
Adjust the height of the device to your preferences
(1,8 m – 2,1 m).
3.3. DEVICE USE
1.
Connect the plug to the socket.
2.
Turn the device on using the pull switch.
3.
Set the desired power:
•
POSITION 0: STOP
•
POSITION 1: 650 W (normal power)
•
POSITION 2: 1300 W (medium power)
•
POSITION 3: 2000 W (maximum power)
4.
Turn the device off after use.
3.4. CLEANING AND MAINTENANCE
a)
Always unplug the device before cleaning it.
b)
Use only non-corrosive cleaners to clean the
surface.
c)
After cleaning the device, all parts should be dried
completely before using it again.
d)
Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
e)
Do not spray the device with a water jet or
submerge it in water.
f)
The device must be regularly inspected to check
its technical efficiency and spot any damage.
g)
Use a soft, damp cloth for cleaning.
h)
Do not use sharp and/or metal objects for
cleaning (e.g. a wire brush or a metal spatula)
because they may damage the surface material
of the appliance.
i)
Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils
or other chemical substances because it may
damage the device.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste
systems. Hand it over to an electric and electrical device
recycling and collection point. Check the symbol on
the product, instruction manual and packaging. The
plastics used to construct the device can be recycled
in accordance with their markings. By choosing to
recycle you are making a significant contribution to the
protection of our environment.
Contact local authorities for information on your local
recycling facility.
Publicidad
