Publicidad
Idiomas disponibles
Idiomas disponibles
Please observe that our equipment was not designed with the intention
of use for commercial or industrial purposes. We assume no guarantee
if the equipment is used in commercial or industrial applications, or for
equivalent work.
6. Safety information
Warning!
This power tool generates an electromagnetic field during operation. This
field can impair active or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly injuries, we recom-
mend that persons with medical implants consult with their physician and
the manufacturer of the medical implant prior to operating the power tool.
m Attention! The following basic safety measures must be observed
when using this compressor for protection against electric shock, and the
risk of injury and fire.
Read and observe these instructions before using the device.
Safe work.
1.
Keep the work area orderly
- Disorder in the work area can lead to accidents.
2.
Take environmental influences into account
- Do not expose electric tools to rain.
- Do not use electric tools in a damp or wet environment. There is a
risk of electric shock!
- Make sure that the work area is well-illuminated.
- Do not use electric tools where there is a risk of fire or explosion.
3.
Protect yourself from electric shock
- Avoid physical contact with earthed parts (e.g. pipes, radiators,
electric ranges, cooling units).
4.
Keep away from children!
- Do not allow other persons to touch the equipment or cable, keep
them away from your work area.
5.
Securely store unused electric tools
- Unused electric tools should be stored in a dry, elevated or closed
location out of the reach of children.
6.
Do not overload your electric tool
- They work better and more safely in the specified output range.
7.
Wear suitable clothing
- Do not wear wide clothing or jewellery, which can become entangled in
moving parts.
- When working outdoors, rubber gloves and anti-slip footwear is
recommended.
- Tie long hair back in a hair net.
8.
Do not use the cable for purposes for which it is not intended
- Do not use the cable to pull the plug out of the outlet. Protect the
cable from heat, oil and sharp edges.
9.
Take care of your tools
- Keep your compressor clean so that you can work well and safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool regularly and have it
replaced by a recognised specialist when damaged.
- Check extension cables regularly and replace them when dam-
aged.
10. Pull the connector out of the socket
- When the electric tool is not in use or prior to maintenance and
when replacing tools such as saw blades, bits, milling heads.
11. Avoid inadvertent starting
- Make sure that the switch is switched off when plugging the plug
into an outlet.
4
GB/IE/NI/CY/MT
12. Use extension cables for outdoors
- Only use approved and appropriately identified extension cables
for use outdoors.
- Only use cable reels in the unrolled state.
13. Remain attentive at all times
- Pay attention to what you are doing. Remain sensible when working.
Do not use the electric tool when you are distracted.
14. Check the electric tool for potential damage
- Protective devices or other parts with minor damage must be care-
fully inspected to ensure that they function correctly and as intended
prior to continued use of the electric tool.
- Check whether the moving parts function faultlessly and do not jam
or whether parts are damaged. All parts must be correctly mounted
and all conditions must be fulfilled to ensure fault-free operation of
the electric tool.
- Damaged protective devices and parts must be properly repaired
or replaced by a recognised workshop, insofar as nothing different
is specified in the operating manual.
- Damaged switches must be replaced at a customer service work-
shop.
- Do not use any faulty or damaged connection cables.
- Do not use any electric tool on which the switch cannot be switched
on and off.
15. Have your electric tool repaired by a qualified electrician
- This electric tool conforms to the applicable safety regulations. Re-
pairs may only be performed by an electrician using original spare
parts. Otherwise accidents can occur.
16. Attention!
- For your own safety, only use accessories and additional equipment
that are indicated in the operating manual or have been recom-
mended or indicated by the manufacturer. Use of other tools or ac-
cessories that those recommended in the operating manual or in the
catalogue could represent a personal danger to you.
17.
Noise
- Wear hearing protection when using the compressor.
18. Replacing the connection line
- If the connection line is damaged, it must be replaced by the manu-
facturer or an electrician to avoid danger. Danger due to electrical
shocks.
19. Filling tyres
- Check the tyre pressure immediately after filling using a suitable
pressure gauge, e.g. at a petrol station.
20. Street-legal compressors in construction site operation
- Ensure that all hoses and fixtures are suitable for the maximum per-
missible working pressure of the compressor.
21. Set-up location
- Only set up the compressor on a flat surface.
22. In case of pressures above 7 bar, it is recommended to equip supply
hoses with a safety cable (e. g. a wire rope).
23. Starting the motor is forbidden if the temperature is below 0°C.
24. Avoid over-stressing the piping system by using flexible hose connections
to prevent kinking.
25. Use a residual current circuit breaker with a trigger current of 30
mA or less. Using a fault-current circuit breaker reduces the risk of
an electric shock.
Publicidad
