IKRA IHS 600 Instrucciones De Manejo página 17

or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction of
a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
GB | Operating Instructions
e) Maintain power tools and accessories. Check
f) Keep cutting tools sharp and clean. Properly
g) Use the power tool, accessories and tool bits etc.
h) Keep handles and grasping surfaces dry, clean
5) Service
a) Have your power tool serviced by a qualified
Safety instructions for hedge trimmers:
-
-
-
-
GB-3
for mis-alignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Keep all parts of your body away from the
cutting blades. Do not try to remove cut-off
matter with the tool running. Do not try to
hold material to be cut off with your hand.
Remove cut-off matter that is stuck be-
tween the blades only with the tool being
switched off! When working with hedge trim-
mers even a short moment of inattentiveness
may result in severe injury.
Hold the power tool by its insulated han-
dling surfaces as the cutting blades might
get in touch with the tool's own power
cable. If the cutting blades should acciden-
tally cut into a live power cable this might turn
metal parts of the tool 'hot' thereby causing an
electric shock.
Carry the hedge trimmer at the handle with
the cutting blades standing still. Always
put on the protection cover when trans-
porting or storing the hedge trimmer. Care-
ful handling reduces the risk of injury through
the cutting blades.
Keep the cable away from the cutting area.
When working with the trimmer the cable
might be hidden in bushes and accidentally
cut through.