Publicidad
Technical Details :
- Power supply
- Flashing beacon output
- Motor output
- Auxiliary power output
- Stop limit and low voltage commands : 24 Vcc
- Working temperature
- Radio receiver
- Op. transmitters
Code
- Bluetooth commands by smartphone:
- Remote controls range in open space:
- Bluetooth range in open space
- Max stored TX codes/Smartphone :
PED)
- Board dimension
- Box dimensions
- Container Module DIN
List of connections :
CN1 :
1 : 230 V ac line input (Phase).
2 : 230 V ac line input (Neutral).
3 : 230 V ac flashing line input (Neutral).
4 : 230 V ac flashing line input (Phase).
5 : Opening motor output.
6 : Common motor output.
7 : Closing motor output.
CN2:
1 : Service power supply output 24Vac 6 W.
2 : Service power supply output GND.
3 : Open-close command button input (NO).
4 : Common GND input.
5 : Safety device input (NC).
6 : Opening stop limit input (NC).
7 : Common GND input.
8 : Closing stop limit input (NC).
9 : Earth antenna input.
10: Antenna hot pole input.
: 230 Vac 50/60Hz 900W(4A) max.
: 230 Vac 50/60Hz
100W Resistive Load max.
50W Inductive Load max.
: 230 Vac 50/60Hz 750 W max.
: 24 Vac 3 W max.
: -10 ÷ 55 °C
: see model
: 12-18-32 bit Fix – 66-80 bit Rolling
IOS/Android
50-100m
:
10-80m
330(CODE
: 104 x 85 mm
: 105 x 95 x 64 mm.
: ABS V-0 (IP40).
Programming by SMARTPHONE :
+
CODE
APP Features by Betech e BeLite :
The SEAV "BeTech" application presents a phone book
containing all the data of the (central) plants produced.
It also allows you to set a Plant Name and a Password (Default:
1 2 3 4) to subsequently access the various configurations; the
possibility to restore a faulty power plant with a new one,
reloading all the information contained in the application's
address book. Furthermore, by entering an email address, it will
be possible to receive a Back Up of all the systems in case of
Smartphone failure. Ability to generate access codes for
activation of the "BeLite" Customer Application, consult the
Diagnostics menu for troubleshooting and much more.
Through the "BeLite" Customer Application, it will also be
possible to send commands via Smartphone also automatically,
i.e. sending the command will only be possible by approaching
the receiver.
Some Operating Mode :
Step by Step ( default ) :
the first command makes the opening until the engine time
expires or when the opening limit has been reached, the
second command closes the window; if a command is sent
before the engine time expires or if one of the two limit switches
is reached, the control unit stops the motion both during the
opening and closing phases. A further command determines
the resumption of motion in the opposite direction.
Inverting :
the first command makes the opening until the engine time
expires, the second command closes the window, if a command
is sent before the expiry of the engine time, the control unit
reverses the motion both in the opening phase and in the
closing one.
Inhibition Open Command :
the first command makes the opening until the engine time
expires, the second command closes the window, if a command
is sent during the opening or pause phase it ignores the
commands given (eg from the loop detector) at each crossing. If
a command is sent during the closing phase, the control unit
reverses the motion.
6
Advanced programming of the control unit can be
performed
via
Smartphone,
dedicated SEAV "BeTech" application.
The application allows the installer to have a
complete work tool for all the installations made.
Once the automation installation has been
completed, on request it will be possible to
configure
a
possible
Application for normal use, via Smartphone for
sending remote commands.
rev. 1.0 01/06/2021
thanks
to
the
"BeLite"
Customer
Publicidad
