Publicidad
Idiomas disponibles
Idiomas disponibles
GB/IE
ical, sensory or mental capabilities or
with a lack of experience and knowl-
edge, must be supervised when using
the product and/or be instructed re-
garding the safe use of the product
and understand the resulting dangers.
- Children are not allowed to play with
the product.
- Maintenance and/or cleaning of
the product is not allowed to be per-
formed by children.
Observe national regulations!
- Observe the applicable national re-
quirements and regulations for the
use and disposal of the product.
WARNING!
1
Risk of injury!
A defective product is not al-
lowed to be used! There is a risk
of injury!
- Do not use the product in the case of
malfunctions, damage or defects.
- Significant danger can occur for the
user in the case of improper repairs.
CAUTION!
2
Risk of injury!
Incorrect installation or use may
result in injury.
- Make sure that all parts are undam-
aged and properly installed. Incor-
rect installation may result in injury.
Damaged parts can affect safety and
functioning.
- The water pressure has to be moni-
tored properly in order to prevent wa-
ter under high pressure from escaping
and causing injury.
- Do not aim the water jet at people or
animals.
6
WARNING!
1
Risk of injury!
Never aim the water jet at
electrical equipment. There
is a risk of electric shock!
- Do not leave the product unat-
tended during operation.
- The product is not suitable as a drink-
ing water pipeline/drinking water
pipeline component.
CAUTION!
2
Risk of slipping!
If the ground is wet, you can slip
on the ground and get hurt.
- Make sure that the ground near the
product is kept as dry as possible.
- Turn the tap off when the product is
not in use.
CAUTION!
2
Damage to property!
Improper handling of the prod-
uct can lead to damage of the
product.
- Do not route the product around cor-
ners or edges or along pointed or
sharp objects. The resulting damage
can cause the product to leak.
- Do not place the product in areas
where vehicles travel. Travelling over
it can cause the product to burst.
- Make sure that dirt particles do not
block or damage the connections or
get inside the product.
- When not using the product: Disman-
tle the product and let out the remain-
ing water from inside the product.
- To avoid frost damage, dismantle the
product in winter, drain it and store it
in a dry place.
Check the scope of delivery
CAUTION!
2
Damage to property!
If you open the packaging care-
lessly with a sharp knife or other
sharp objects, the product can
quickly be damaged.
- Be very careful when opening.
- Take the product
1
and all accesso-
ries out of the package.
- Check that the delivery is complete
(see "3. Scope of Delivery").
- Check to see if the product
1
or the indi-
vidual parts are damaged. If so, do not
use the product. Contact the manufactur-
er at the indicated service address.
Start-up
Connect the tap
1. Turn the tap closed.
2. Make sure that the hose connector
valve
5
is set to (2) "OFF" position
and is at a right angle to the product,
see Fig. B-(A).
Attachment to the water connec-
tion with (DN 15) 21 mm (G ½")
- outer thread Fig. A-(A)
1. Screw the tap connector
2
onto the tap.
2. Screw the hose connector valve
adapter
3
onto the tap connector
3. Push the hose connector valve
4
the hose connector valve adapter
until it clicks in.
4. Check the tightness.
Attachment to the water connec-
tion with (DN 20) 26.5 mm (G
¾") - outer thread Fig. A-(B)
1. Screw the hose connector valve
adapter
3
onto the tap.
2. Push the hose connector valve
4
the hose connector valve adapter
until it clicks in.
3. Check the tightness.
Operation
NOTE!
Convince yourself before the first
use of the tight fit of all connec-
tions. If necessary, tighten them
a little.
1. Unroll the Product
1
completely be-
fore use.
2. Turn on the tap only a little at first and
increase the water pressure evenly.
The product will roll out.
3. Once the product is completely un-
rolled, open the valve on the hose
connector valve
5
by setting it to po-
sition (1), see Fig. B-(A).
The product is ready to use.
4. Once you no longer need the prod-
uct, shut off the water supply by turn-
ing off the tap.
5. Open the hose connector valve
by turning the valve to position (1)
and allow the remaining water to
run off. After the water has drained,
the Product will return to its original
length.
NOTE!
- To release the hose from the tap or the
hose connector valve adapter
2
.
the ring of the hose connector valve
onto
downwards as marked with the arrow
3
and unlock the coupling and pull off
the hose connector valve
4
Cleaning and care instruc-
tions
CAUTION!
2
Danger of material damage!
- only clean with a damp cloth
onto
- only use a mild detergent
3
- do not use any strong detergents
and/or chemicals
- do not use sharp-edged tools such as
GB/IE
5
3
, slide
4
,
.
7
Publicidad
