Publicidad
Idiomas disponibles
Idiomas disponibles
Technical data
Drilling machine and impact drill
Type
Supply.voltage.
Power.frequency.
Power.input.
Speed.under.load
.
1st.speed.gear.
.
nd.speed.gear.
Idle.speed
.
1st.speed.gear.
.
nd.speed.gear.
Number.of..impacts
.
1st.speed.gear.
.
nd.speed.gear.
Speed.pre-selection.
Safety.clutch.
Extent.of.chuck.ø.
Thread.on.spindle.
Drilling.ø.max.
.
into.steel.
.
into.wood.
.
into.concrete.
.
.
Clamping.neck.ø.
Weight.
Protection.class.
Controls
1 ............ Chuck with ring gear
2 ............ Clamping neck
3 ............ Latching pin
4 ............ Switch / controller
5 ............ Speed pre-selection wheel
6 ............ Air vents
7 ............ Gear-shifting lever
8 ............ Hammer gear button
9 ............ Additional handle
10 . ......... Stop bar
11 . ......... Chuck hook
12 . ......... Spots on spindle
13 . ......... Socket screw wrench
14 . ......... Quick-tightening chuck
15 . ......... Wing screw
16 . ......... Wing screw
17 . ......... Wing screw
The displayed or described accessories need not be included in the delivery
package.
Double insulation
To ensure maximum safety of the user, our tools are designed and built to
satisfy applicable European standards (EN standards). Tools with double
insulation are marked by the international symbol of a double square. These
tools must not be grounded and a two-wire cable is sufficient to supply them
with power. Tools are shielded in accordance with EN 50114.
Use
The machine is intended drilling in wood, metal, ceramic and plastic. Machines
with electronic control and right/left rotation are also suitable for screwing
and thread cutting ( Only for soft screwdriving applications).
EVP 16-2F3:
The machine is intended for impact drilling in brick, concrete and stone as
well as for drilling in wood, metal, ceramics and plastics. Machines with
electronic control and right/left rotation are also suitable for screwing and
thread-cutting.
The user alone is responsible for any liabilities caused by usage other than
intended.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
full.drill.bit.
annular.bit.
.
.
.
EV 16
30.V.
50–60.Hz.
90.W.
400.min
.
-1
û.
70.min
.
-1
û.
û.
û.
û.
û.
3–16.mm.
5/8"–16UN–A.
16.mm.
55.mm.
û.
û.
57.mm.
4.35.kg.
II./.
Commissioning and use
Any unauthorised use might cause damage to the tool. Therefore follow
these instructions:
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or stoppage.
- Always change the speed gear when the machine is idle or at the
machine slow-down at low speed, in no case during the drilling or
when the machine is otherwise loaded.
Check whether the data on the name plate correspond with the actual
power supply voltage. Tools designed for 230 V may be connected also
to 220 / 240 V.
Additional handle
For safety reasons always use the enclosed auxiliary handle (9). Fasten the
auxiliary handle to the clamping collar (2) with the wing bolt (15).
By loosening the wing bolt (16) the drilling depth can be adjusted with the
depth stop adjustment (10).
The auxiliary handle is used to guide the machine securely, especially with
sudden occuring reaction torque (e. g. jamming of the drill bit).
By loosening the wing bolt (17) the position of the auxiliary
handle can be adjusted in length direction.
Apply the pressure required for work against the handle only
and not against the auxiliary handle (9).
Clamping a drill
Insert tool and tighten equally in all 3 holes with chuck key.
Switching on and off
By pressing the switch button (4) the machine activates and releasing the
button stops it.
Permanent run
By pressing the switch button (4) to the stop and simultaneous pressing the
latching pin (3) permanent run is achieved.
Repeated pressing the switch button (4) and its release the permanent run
is discontinued.
English
EVP 16-2F3
30.V
50–60.Hz
90.W
0–550.min
-1
0–980.min
-1
0–960.min
-1
0–1.700.min
-1
0–11.000.min
-1
0–19.500.min
-1
ü
û
3–16.mm
5/8"–16UN–A
16.mm
55.mm
30.mm
55.mm
57.mm
4.6.kg
II./
11
Publicidad
