Schumacher SJ1332 Manual Del Usuario página 5

5.3 USING THE WORK LIGHT
The work light is controlled by a sliding ON/
OFF switch located on the front of the unit.
• Make sure the lamp is turned OFF when
the unit is being recharged or stored.
• Position the unit on a flat, stable surface
near the intended work area.
• Ensure the battery clamps are securely
clipped on the storage holders.
5.4 POWERING A 12V DC DEVICE
The unitis a power source for all 12V DC
accessories that are equipped with a 12V
accessory plug. Use it for power outages
and on fishing or camping trips.
NOTE: Do not power a 12V device with
the unit while charging the internal battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC
power outlet on the unit.
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the unit to run
appliances that draw more than 20A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the unit immediately after
unplugging the 12V DC device.
5.5 USING THE AIR COMPRESSOR
NOTE: To prevent overheating, the
compressor has built-in thermal protection
that will turn the compressor off before it
overheats. If the compressor shuts off,
wait a few minutes and it will automatically
restart when the compressor cools.
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air
compressor unattended during use.
1. Remove the air compressor hose from
the storage compartment.
2. Connect the adapter to the valve stem
by threading it onto the end. If necessary,
use one of the additional adaptors.
3. Turn ON the inflator power switch and
inflate to the desired pressure or fullness.
4. When the desired pressure is reached,
put the inflator power switch to OFF,
open the thumb latch and remove the
connector from the valve stem.
5. Allow unit to cool.
6. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI maximum.
5.6 USING THE INFLATOR
RISK OF EXPLOSION.
Read instructions of the product being
inflated before using the inflator.
Avoid overinflation, do not exceed the
manufacturer's recommended pressures.
Do not leave the inflator unattended
during use.
1. Ensure the battery clips are securely
on the storage holders.
2. Attach the corrugated hose with end
adapter to the high-flow inflator outlet
located near the Compressor/Inflator
switch on the back of the unit.
3. The main accessory adapter attached
to the corrugated hose accommodates
up to 4 sizes. If another size is needed,
an additional adapter can be attached to
the end of the main accessory adapter.
4. Insert the adapter into the product to be
inflated.
5. Push the Compressor/Inflator switch to
the INFLATOR position and inflate the
product.
6. When the product is inflated to the
desired level, push the Compressor/
Inflator switch to the OFF position and
remove the adapter.
Estimated time for inflating
Vehicle tires 13-16"
Bike tires
Sports balls
These times are approximate. Use the air
compressor gauge to ensure the proper pressure
has been reached. Do not overinflate.
5.7 USING THE DEFLATOR
1. Ensure the battery clips are securely
on the storage holders.
2. Attach the corrugated hose with the
end adapter to the high-flow deflator
outlet, which is located on the side of
the unit.
3. The main accessory adapter attached
to the corrugated hose accommodates
up to 4 sizes. If another size is needed,
an additional adapter can be attached
to the end of the main accessory
adapter.
4. Insert the adapter into the item to be
deflated.
5. Push the Compressor/Inflator switch to
the INFLATOR position and deflate the
item.
• 5 •
6-24 minutes
1-3 minutes
30 seconds