Publicidad
Idiomas disponibles
Idiomas disponibles
7.
LCD Display: This multifunction display will detail all chase and program that pertains to the current operating
mode of the pack.
8.
Channel Fuses: Each of the four channels is protected by a 10A fuse. These fuses prevent you from overloading
and damaging your pack. Be sure to always replace with the exact same type fuse.
9.
Power Switch: This switch controls the units main power.
10. Power Cord: Plug this cord into a matching power supply for your area.
11. DMX Input: This connector accepts your DMX input signal.
12. DMX Output: This connector sends your DMX input signal through to the next DMX device.
Operation mode
The unit has two different operating modes. This unit can be used as a four channel chaser or as a 1, 2, or 4 channel
DMX dimmer pack. Please follow the instructions blow to operate the unit in your desired mode.
Chase mode
Use this operating mode only if you are planning on using your TR-D4 as a four channel chaser. This device has 16
built in programs, you may select any of these programs or set the pack to chase in a random sequence of all 16 built in
programs for a more dramatic light show. You may control the speed at which the programs will chase.
1.
Connect your lighting effects to the any of the eight power sockets on the pack
2.
Use the mode button to select chase mode: Chase mode is indicated by "PA" followed by numbers 01-16. "PA" is
Programmed Applied. If "A" appears in the LCD display you are in DMX mode, "A" stands for address.
3.
Set you desired chase pattern: Once you have selected the chase function use the Menu button to select your
desired chase. The chase pattern is represented in the LCD display by "P" followed by two numbers. You may
select any of the built in 16 programs to run at a single time.
4.
Set you desired chase speed: At this point you may change the program chase speed. While in chase mode, tap
on the MENU button until the "SP" followed by two numbers is displayed in the LCD. Then use the UP and DOWN
buttons to adjust the chase speed. A value of 99 will give you the fastest chase speed (about 1/10th of a second).
A value of 01 will give you the slowest chase speed (one step every 30 sec.).
5.
You may now change the light intensity: Use the MENU button to select "d" in the LCD. Use the UP and DOWN
arrow keys to change the light output intensity. 00 will give the lowest output and 99 will give you full intensity.
DMX mode
Use this operating mode only if you plan to use your pack as a DMX dimmer. This function will allow you to turn on and
control the intensity of non-DMX with the use of a DMX controller. On, off, and dimming functions can be performed
through this pack. You may also set your dimmer pack to function as a 1, 2, or 4 channel DMX dimmer pack, which
means you can combine the output functions.
DMX Operation:
1.
Plug in a DMX controller to your dimmer pack via the 3-pin XLR cables.
2.
Connect your lighting effect to any of the eight power sockets on the front of the pack.
3.
Decide if you are going to use your dimmer pack as 1, 2, or 4 channels. This function allows you to:
A.
Control the output to all four outlets with one DMX channel.
B.
Group outlet channels one and two and group outlets channels three and four. The first group will be
controlled by one DMX channel and the second group will be controlled by another DMX channel. This gives
the pack a DMX value of two.
C.
The default setting is a four channel DMX switcher, each channel is controlled by one DMX channel.
4.
To change the channel function mode be sure you are in DMX mode. Use the MENU button to select "CH"
followed by two digits. Then use the UP and DOWN arrow buttons to change the setting from 01, 02, or 04. Your
dimmer pack is initially set as a four channel DMX switcher.
5.
The dimmer pack is initially set to be activated by DMX address one. To change this setting be sure you are in
DMX mode. Use the MENU button to select the address settings, this will be indicated by an "A" in the first character of
the LCD followed by three numbers. Use the UP and DOWN arrow buttons to select your desired DMX address.
Remember the DMX address tells your DMX controller what channel to activate the pack's functions.
6.
Once you have set the pack's DMX address be sure your controller's address matches that of the pack's.
7.
Your pack will now operate as DMX dimmer, you may control the light output intensity through your DMX
controller. 0 will give no output and 100 will give you full output.
Fuse Replacement
To replace the protective fuse, use a flat head screwdriver to unscrew the fuse holder. Pull out the old fuse and replace
it with a new one. Insert the fuse back into slot and tighten. Always replace with the exact same type fuse remove
unless otherwise specified by an authorized our company service technician.
CAUTION: Always disconnect the units main power before performing any type of service or fuse replacement.
Power Supply
Before plugging your unit in be sure the source voltage in your area matches the required voltage for your TR-D4. The
unit is available in a 120V and 240V version. Because line voltage may vary from venue to venue, you should be sure to
plug your power supply into a matching wall outlet before attempting to operate you controller.
Product Description
User manual Dimmer 4 canales TR-D4 | Triton Blue | Rev. Sep 2013 | www.triton-‐blue.com
Publicidad
