Grounding Instructions; Service; Introduction; Using An Hvlp Spray System - CAPspray CS8100 Manual Del Propietário

Grounding Instructions

This product must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product
is equipped with a cord having a grounding wire with an
appropriate grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
DANGER — Improper installation of the grounding plug can
result in a risk of electric shock. If repair or replacement of the
cord or plug is necessary, do not connect the green grounding
wire to either flat blade terminal. The wire with insulation
having a green outer surface with or without yellow stripes is
the grounding wire and must be connected to the grounding
pin.
Check with a qualified electrician or serviceman if the
grounding instructions are not completely understood, or if you
are in doubt as to whether the product is properly grounded.
Do not modify the plug provided. If the plug will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
This product is for use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug illustrated below. A
temporary adapter which looks like the adapter illustrated in
the figure below may be used to connect this plug to a 2 pole
receptacle as shown if a properly grounded outlet is not
available.
The temporary adapter should be used only until a properly
grounded outlet as shown below can be installed by a qualified
electrician. The green colored rigid ear, lug, or the grounding
wire extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place
by a metal screw.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
Metal Screw
CAUTION
Use only a 3-wire extension cord that has a 3-blade
grounding plug and a 3-slot receptacle that will accept the
plug on the product. Make sure your extension cord is in
good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your
product will draw. For lengths less than 25 feet, No. 16
AWG extension cords should be used. Between 25 feet
and 50 feet, the minimum gauge is 14 AWG. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. If an extension cord is
to be used outdoors, it must be marked with the suffix W-
A after the cord type designation. For example, a
designation of SJTW-A would indicate that the cord would
be appropriate for outdoor use.

Service

Should your spray system need service during the warranty
period, return your unit and the proof of purchase to the
distributor where it was purchased. At our option, the unit will
be repaired or replaced. In a continued commitment to
improve quality, we reserve the right to make component or
design changes when necessary.
© SprayTECH Corporation. All rights reserved.
Adapter
Tab for
Grounding Screw
3

Introduction

This High Volume/Low Pressure (HVLP) spray system is
designed for applying coatings to surfaces that can be sprayed
faster than brushing or rolling and are too small for traditional
airless sprayers. Components of this system include a power
switch, a power cord, a filter warning light, a replaceable fuse,
a dual filtration system, a cup holder, an air hose, and an air
outlet.
Air Outlet
Air Hose
Filter
Power Switch
With this HVLP spray system, you can achieve the highest
quality professional finish possible with little or no preparation
or setup time. Please review all the information contained in
this manual before operating the system.

Using an HVLP Spray System

Refer to the following information to operate and understand
your HVLP spray system.

Setup

Use the following procedure to set up your HVLP spray system
for operation.
1. Plug the turbine power cord into a grounded, 3-slot
receptacle.
WARNING
Keep the turbine at the maximum possible distance from
the spray area to safeguard against explosion or fire that
may be caused by sparking electrical parts.
2. Prepare your spray gun for operation. Refer to your spray
gun manual for material preparation, setup, and spraying
information.
3. Attach the air hose to the air outlet on the turbine.
4. Attach the air hose to the air inlet on your spray gun.
5. Turn on the turbine and begin spraying.
Cup Holder
Filter (in end
of filter can)
Fuse
Filter
Warning
Light
Power Cord
English