PLUS200 EXPERT
VISUALIZACIÓN DE LAS ALARMAS - DISPLAYING ALARMS
5.15
Para visualizar las alarmas registradas es necesario,
mediante el teclado frontal que se muestra en el apdo.
5.2, :
1.
Pulsar
la
tecla
simultáneamente durante 5 s. El sector A1 de la
pantalla LCD comienza a parpadear.
2.
Seleccionar el mes y el día como en la visualización
de los datos. A este punto se visualiza la primera
alarma registrada del día seleccionado.
3.
Con la tecla (
) y (
registros de alarmas. Si en la fecha seleccionada no
hay datos registrados, la pantalla lcd visualiza la
sucesiva alarma útil.
4.
Pulse la tecla 1 durante 5 s para regresar a la
visualización normal.
ALMACENAMIENTO DE DATOS EN LA TARJETA SD – SAVING DATA ON THE
5.16
Mediante el programa TeleNET
consultar, visualizar gráficos e imprimir de forma simple y
rápida los datos descargados con la tarjeta de memoria
de los cuadros PLUS200 Expert.
Para el almacenamiento de los datos de la memoria
interna en la tarjeta
es necesario:
1.
Usar modelos de
GB y con velocidad de 80x (Ultra-Speed) o 150x
(Extreme-Speed). La tarjeta se debe formatear
con FAT16.
2.
Introduzca la tarjeta de memoria
en el frente del cuadro (Vea el capítulo 5.4
relativo al slot secure digital).
3.
Pulse
la
tecla
simultáneamente durante 5 s.
4.
Cuando aparece la pregunta SAvE no/YES,
seleccione YES con las teclas (
confirme el almacenamiento con la tecla
5.
Durante todo el almacenamiento el mensaje
SAvE y el indicador de estado de la secure
digital parpadean.
6.
Al finalizar el almacenamiento se emite una
breve señal sonora y aparece el mensaje donE.
7.
En caso de error relativo a la memoria
emite una señal sonora larga y parpadea el
mensaje Err Sd con uno de los códigos de error
indicados a continuación:
MANUAL DE USO Y MANTENIMIENTO
Pág. 26
USE AND MAINTENANCE MANUAL
y
la
tecla
) se pueden recorrer los
es posible archivar,
con capacidad inferior a 2
en el slot
y
la
tecla
) y (
.
se
5 - Programación de datos - Parameter programming
To display alarm recordings it is – via the keypad on the
front panel illustrated in section 5.2 – necessary to:
1.
Press key
for 5 seconds. The A1 field on the LCD display will
start flashing.
2.
Select month and day as described in 5.12
(displaying recorded data). At this point the first
recorded alarm of the selected day is displayed.
3.
Use the (
) and (
recordings. If no recorded alarms are available for the
selected day, the LCD display will show the next
alarm recording.
4.
Press key 1 for 5 seconds to return to the standard
display mode.
It is, via the TeleNET
possible to store, consult, display graphs and print data
downloaded with the
devices.
To save data from the internal memory on the
is necessary to:
1.
Use
models with a capacity of no more than
2 GB and speeds of 80x (Ultra-Speed) or 150x
(Extreme-Speed). The card must be formatted
with FAT16.
2.
Insert the
front of the panel (see chapter 5.4 on the secure
digital slot).
3.
Press
the
simultaneously for 5 sec.
4.
When the question SAvE
) y
select YES with the (
confirm saving with the key
5.
When saving is in progress the legend SAvE and
the secure digital status light flash.
6.
When saving is over a short beep is emitted and
the legend done appears.
7.
In the event of a
beep is emitted and the legend Err Sd flashes
with one of the following error codes:
and the
key simultaneously
) keys to scroll the alarm
SD
programme, easily and quickly
card from PLUS200 Expert
memory card in the slot on the
key
and
the
no/YES appears
) and (
) keys and
.
card memory fault a long
Rev. 01-16
CARD
card it
key