Selecting Mode - Milwaukee 2774-20 Manual Del Operador

3. Insert the battery pack.
4. Press the hold pressure
5. Run the tool until the cy-
cle completes, and the
pressure indicator lights
green.
6. Press and hold the manual
release button for two sec-
onds, then release both
buttons.
7. Repeat steps 4-6 three to
four times.
NOTE: While bleeding the
accessory, make sure the oil
level does not drop below the
oil sight line. Refill the reservoir
if necessary.
Removing/Attaching the Remote Cord
To remove the remote cord, twist the cord grommet
loose and pull the cord away from the remote or tool.
To attach the remote cord, line up the keys of the
cord to the keys of the remote or tool. Push the cord
into the remote or tool and twist the cord grommet
until tight.

Selecting Mode

The pump features three modes of operation:
Auto-Dump mode
soon as 10,000 psi is reached.
Hold Pressure mode
manual pressure release button is pushed or the
retract button is pushed on the remote.
Wireless mode
pump via bluetooth signal. The pump will run to full
pressure and then release. The remote must be re-
attached for the next application. WARNING! Once
the pump is started using wireless mode, it will run
to completion and cannot be halted.
ONE-KEY™
To learn more about the ONE-KEY™ function-
ality for this tool, please reference the Quick
Start guide included with this product or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
button.
unloads pump pressure as
holds pressure until the
allows the user to activate the
WARNING
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken first.
2
To reduce the risk of injury, always wear proper
sec
eye protection marked to comply with ANSI Z87.1.
Before using:
• Inspect pump, hoses, couplers, and fittings for wear
or damage. Replace worn, damaged, or missing
components with manufacturer's replacement parts.
WARNING! Do not use hands to check for leaks.
High pressure oil easily punctures skin, causing
serious injury, gangrene, or death. If injured, seek
medical help immediately to remove oil.
• Ensure pump is in the desired mode of operation.
• Ensure pump is below the maximum tilt angle.
• Check the oil level and adjust if necessary. Low oil
may result in injury or property damage. For best per-
formance, always use MILWAUKEE Force Logic™
Hydraulic Oil (49-32-0110) to refill the reservoir.
• Follow accessory manufacturers' installation instruc-
tions. Other uses may cause damage to the tool,
accessories, and workpiece.
• Bleed the system if necessary. WARNING! If the hose
and accessory retain pressure after the pump has
relieved pressure (either by using the Manual Pres-
sure Release Button or at the end of an operation),
relieve pressure in a safe manner and replace the
hose and remote pump couplers.
To operate with the remote cable-connected to
the pump:
1. Depressurize the tool by holding down the manual
pressure release button for five seconds.
2. Connect the hose coupler to the pump coupler.
3. Connect the tool head to the hose.
4. Insert the battery pack.
5. Press and select the preferred mode of operation
between auto-dump
6. Press and hold the ad-
vance button
remote.
7. If in auto-dump mode
the pump will release
pressure as soon as
10,000 psi is reached.
The pump will switch off
and the indicator will
light.
7
OPERATION
To reduce the risk of arc flash,
electric shock and property
and hold pressure
on the
,
.