Publicidad
2
PART NAMES AND FUNCTIONS
(1) Front panel
q
MIC LEVEL control
• Adjust the level of Mic signal.
w
MIC BALANCED INPUT terminal
• Accepts an balanced microphone with 1/4" TRS
mono terminals.
• Pin layout: Tip=Hot Ring=Cold Sleeve=GND
e
GAIN
• Adjusts the gain of each input channel.
r
CUE buttons
• These buttons are used to activates a channels
"CUE" mode, the indicator above the cue button
will glow when cue mode is activated. Cue mode
will send a channels incoming signal to the
headphones.
t
Source EQ controls
• Contour the frequency response of the selected
inputs.
HI:
• Adjusts the high-tone sound –19 dB to +10 dB.
MID:
• Adjusts the high-tone sound –26 dB to +10 dB.
LOW:
• Adjusts the high-tone sound –26 dB to +10 dB.
NOTE:
Clipping may occur if adjustments are set to harsh.
y
Channel Fader
• Controls the channel output level.
u
Crossfader
• Fades the overall mixer output between channels 1
and 2.
i
Level meter mode select switch
• The position of this switch will determine the Level
Meter mode. In the "MASTER" position, the meter
will detail the out level of the left and right channels.
In the "PGM 1/2" position, the left side of the
meter will indicate monaural level of the PGM 1 and
the right side of the meter will indicate monaural
level of the PGM 2.
(Refer to page
.)
II
o
HEADPHONE output terminal
• Accept 1/4" stereo headphone plugs.
!0
PHONES LEVEL control
• Adjusts the headphone output level.
!1
Headphone PAN control
• This function allows you to monitor the CUE level as
well as the MASTER output in your headphones. A
CUE Level may only be monitored of the CUE signal
is selected.
• It changes the relative levels of the CUE and
MASTER mixed together in both ear cups.
!2
Input select switch
• Switches between the PHONO/LINE and LINE
inputs.
• When the lever of switch is vertical position, the
LINE2 or LINE4 input is selected.
• When
the
lever
of
switch
is
slope,
PHONO1/LINE1 or PHONO2/LINE3 input is
selected.
!3
MASTER LEVEL control
• Adjust the level of the MASTER output.
!4
Level Meter
• The dual LED's indicators are used to detail either
the master output level, a combination of the
master output level and the CUE signal level, or the
PGM1/2 monaural level.
!5
MASTER BALANCE control
• Adjust the L/R balance of the MASTER outputs.
!6
Power operation switch (POWER)
• Selects power "ON" or "OFF".
NOTE:
Whenever the power switch is in the OFF state, the
AC adaptor is still connected on AC line voltage.
Please be sure to unplug the cord when you don't use
for along time.
(2) Rear panel
!7
AC inlet (AC IN)
• Input connection for the included AC adaptor.
NOTE:
Use specified attached AC adaptor only.
!8
Balanced MASTER OUT terminals
(BALANCED)
• These 1/4" TRS terminals provide a balanced line
level output.
• Connect these terminals to the balanced analog
input terminals on an amplifier or console.
• Pin layout: Tip=Hot Ring=Cold Sleeve=GND
!9
Unbalanced MASTER OUT terminals
• This stereo pair of RCA terminals provides an
unbalanced line level output.
• Connect these terminals to the unbalanced analog
input terminals on an amplifier or console.
@0
LINE2, 4 input terminals
• These stereo pair of unbalanced RCA terminals are
inputs for any line level device.
the
@1
PHONO1, 2 / LINE1, 3 input terminals
• These stereo pair of unbalanced RCA terminals are
inputs for a PHONO (RIAA) stage for magnetic
(MM) cartridges or a LINE stage suitable for any
device, such as a CD player.
@2
PHONO1, 2 / LINE1, 3 switches
(LN / PH)
• These switches change the input from PHONO to a
LINE level input.
• These switches set a LINE level input when
turntable is not connected.
NOTE:
Always be sure main power is shut off before change
the position of the Line Level Selector Switch.
@3
Phono ground screw (GND)
• This screws provide a place to connect the ground
wire from a turntable.
• This terminal is exclusively for a turntable ground
and not a safety earth ground.
2
ENGLISH
3
CONNECTIONS
Refer to the connection diagram below.
1. Make certain AC power is off while making
connections.
2. Quality cables make a big difference in fidelity and
punch. Use high-quality, audio cables.
3. Do not use excessively long cables. Be sure plugs and
terminals are securely fastened. Loose connections
cause hum, noise, or intermittents that could damage
your speakers.
4. Connect all stereo input sources. Then connect any
effects into the stereo effect, if used. Connect your
microphone(s) and monitor headphones. Make sure all
faders are at "zero" and the unit is off. Take care to
connect only one cable at a time. Pay attention to L and
R position of terminals, on both the DN-X050 and
outboard gear.
5. Connect the stereo outputs to the power amplifier(s)
and/or tape deck(s) and/or MD recorder(s) and/or CD
recorder(s). Plug the DN-X050 into AC power outlet.
NOTE:
Always switch on your audio input sources such as CD
players first, then your mixer, and finally any amplifiers.
When turning off, always reverse this operation by
turning off amplifiers, then your mixer, and then input
units.
Publicidad
