Filter Replacement List; Step 10 Filter Changing Procedures; Step 11 Recommended Sanitizing Procedure; Step 12 Service And Maintenance Recommendations - Krystal Pure KR5 Manual Del Propietário

FILTER REPLACEMENT LIST

Part Numbers
R/O Model
PRE SEDIMENT
KR5
N/A
KR10 P1 #136-1110-1
KR15 N/A
Replacement
6mo. - 1yr.
Frequency
container and ½ cup of R/O product water in the
other container. Send both samples to the manu-
facturer along with your contact information.
To order replacement filters or locate a source
in your area call the factory: AmeriFlow™ Water
Systems Inc. (602) 275-4188.

STEP 10 FILTER CHANGING PROCEDURES

Sediment and Carbon: Turn Filter Pac/R/O mod-
ule ball valve to off position. Turn tank ball valve
off. Turn on R/O faucet to help de-pressurize
system. Unscrew filter bowls by turning count-
er-clockwise. Remove old filters and discard.
Clean filter bowls if needed in warm, soapy wa-
ter. Insert new filters into appropriate filter bowls.
Make sure O-ring at top of filter bowl is clean, lu-
bricated and seated properly when tightening. If
changing the post filter, do so now following the
same procedure as the pre-filters. Follow Step 7:
System Start-Up Procedures. Check for leaks and
adjust as necessary.
R/O Membrane: Turn R/O tank and water supply
off. Turn on R/O faucet to help de-pressurize sys-
tem. Disconnect white tube going into membrane
housing. Unscrew end cap of membrane hous-
ing. Have a towel and a bucket handy because
some water will pour out. Pull out old membrane
and clean membrane housing if necessary with
warm, soapy water. Insert new membrane in the
same direction as old membrane. Push firmly up
to properly seat R/O membrane. Replace end cap
and reconnect white tube to membrane housing.
Follow Step 7: System Start-Up Procedures. Sys-
tem should be sanitized each time the membrane
is changed. (See Recommended Sanitizing Pro-
cedures). Test TDS (Total Dissolved Solids) rejec-
tion rates and be sure the rates are over 75%. A
TDS monitor is optional on some models and in-
cluded on others. If your unit did not come with
a monitor, you can order one or seek advice from
a local water treatment service company. A new
PRE CARBON MEMBRANE
CB05 #135-1210-1 TFC-24 #138-
124-1
CB05 #135-1210-1 TFC-24 #138-
124-1
CB05 #135-1210-1 TFC-24 #138-
124-1
1 yr. 2-5 yrs.
membrane should perform between 90-98% TDS
removal. Check for leaks and adjust as necessary.
STEP 11 RECOMMENDED SANITIZING
PROCEDURE
The manufacturer recommends having your sys-
tem professionally sanitized once a year. The best
time to sanitize is when changing all the filters
and/or when changing the membrane.
1. Drain all water from R/O tank by turning on
2. Carefully put 2 capfuls of household bleach
3. Turn water supply on (open ball valve on
4. Let entire system sit for about 30 minutes
STEP 12 SERVICE AND MAINTENANCE
RECOMMENDATIONS
All Reverse Osmosis systems require periodic
maintenance to insure the continuation of wa-
M.A.P.™ CARBON
N/A
N/A
CB-A #135-1210-2
1 yr.
R/O faucet until water stops flowing. Follow
Filter Changing Procedures (assuring ball
valve on tank and Filter Pac/R/O module
are in off position). Remove old pre-filters
and membrane from housings. Remove the
post-filter from the filter bowl canister.
into the empty filter bowl canisters. Re-install
filter bowls without filters. CAUTION: Be care-
ful not to splash bleach on hands or surfaces.
tank and R/O module) and let system fill for 4
minutes with tap water. Shut system off. Turn
R/O faucet on until water comes out and then
shut it off.
to sanitize. Then turn on R/O faucet and let
system drain until empty. Turn off water sup-
ply valves and empty water in filter bowls.
Re-install filter bowls. Turn the water supply
on again. Turn off faucet and let system re-
fill with tap water as before. Drain again. In-
stall new filters following the Step 10: Filter
Change Procedures. Follow Step 7: System
Start-Up Procedures.
POST CARBON
CB #135-1210-2
CB #135-1210-2
CB #135-1210-2
1 yr.
9