Installation; Racking; Cooling; Input Cable Connections - D.A.S. PS Serie Manual De Usuario

INSTALLATION

Racking

All amplifiers are 19-inch rack mount width.
PS-400
and are 1U DIN in height.
PS-2400
are 2U DIN in height.
Four front-panel mounting holes are provided for
use with M5 or M6 or 1/4" screws. To avoid bending
the chassis in rack mounting applications where the
rack will be transported, mount the amplifiers to the
back of the rack using the rear mounting holes.
Alternatively, place the bottom amplifier against the
base of the rack and pile the amplifiers with no
clearance in between.
Amplifier's dimensions can be found on the "Line
Drawings" section of this manual.

Cooling

A fan cools the aluminium heat
sinks from back to front.
Fan cooling permits airflow
through the most vital parts of the
amplifier.
When mounting the unit onto a
19-inch rack, a rack cooling
system is not required, since the
air is exhausted out through the
front grille.
However, the rack must not be
sealed, and it should at least have
a large enough ventilation grille to
allow air into the rack.

Input cable connections

The Input Cabling Appendix shows balanced and
unbalanced connection from
connector to the amplifiers.

Speaker cable connections

Either the binding posts
PS-800,PS-1400
connectors (
used.
The binding posts can be used with bare wire or
banana connectors. In either case, ensure that you
remove the required length of cable sleeve that allows
for the conductor itself to be hidden. Always note
polarity (red=+,black=–).
Speakon connectors offer quick connection for
portable applications. To
connection, plug the male connector into the outlet
and rotate it clockwise. It will then lock into place and
be ready for use.
The Appendices of this manual include a table to
aid in the selection of the appropriate cable gauge.
PS-200
PS-800 PS-1400
, and
Consumos eléctricos / Power consumption (Amperios / Amperes)
Potencia / Power
PS-200
8+8 ohm
4+4 ohm
Puente/ bridge
PS-400
8+8 ohm
4+4 ohm
Puente/ bridge
PS-800
8+8 ohm
4+4 ohm
Puente/ bridge
PS-1400
8+8 ohm
4+4 ohm
Puente/ bridge
PS-2400
8+8 ohm
4+4 ohm
2+2 ohm
Puente/ bridge
different types of
or the Speakon
PS-2400
and ) can be
enable a Speakon
Manual del Usuario / PS / User's Manual
Connection to mains
Nominal AC voltage will always be indicated on the
back panel. 230V and 115V versions are available.
Nominal AC voltage range on 230V version, is
230V ±10%, that meaning it can work from
to 253V.
Likewise, on the 115V version, the nominal AC
voltage range is 115 V ±10%, that meaning it can work
from 103V up to 127V.
Be sure your unit has the nominal AC voltage for
your country.

Power consumption

Can be seen on the accompanying table for 230V.
Double the ratings to
consumption.
Standard IEC-60065:2001
consumption using pink noise at 1/8th of rated power.
This is done to represent the current requirements to
reproduce a typical musical programme.
Max 1/3
0.87 0.31
1.57 0.57
8 ohm 1.6 0.6
1.64 0.57
2.98 1.06
8 ohm 3.0 1.1
2.8 0.98
5.28 1.82
8 ohm 5.3 1.85
5.2 1.82
9.59 3.41
8 ohm 9.6 3.45
12.8 5.9
20.1 9.6
--- ---
8 ohm 20.5 9.6
The 1/3rd power rating represents a worst case
scenario, while the maximum power represents
consumption with sine wave signal, which will never
occur in practice.
207V up
get the 115V current
specify AC
Sin señal
1/8
/ idle
0.15 0.05
0.25 0.05
0.25 0.05
0.27 0.08
0.47 0.08
0.5 0.08
0.48 0.15
0.81 0.15
0.85 0.15
0.84 0.2
1.48 0.2
1.5 0.2
2.8 0.5
4.8 0.5
8.5 0.5
4.7 0.5
5
EN