Descaling; Storing Instructions; Troubleshooting; Warranty - Bella 14762 Manual De Instrucciones

Descaling

Minerals, lime and calcium found in hard-water areas can accumulate and affect the operation of your Kettle.
Depending on water conditions and frequency of use, your Kettle should be cleaned once a month with
distilled vinegar or fresh lemon juice to remove scale.
1. Before cleaning your Kettle, make sure the power base is unplugged and the Kettle is cool.
2. Fill the Kettle with 1 part white vinegar or lemon juice to 3 parts cold water.
3. Allow the filled Kettle to stand for 1 hour; then bring the Kettle contents to a boil.
4. Empty the Kettle, rinse thoroughly, then repeat this process 1 to 3 times.
5. After decalcifying, rinse the Kettle thoroughly then re-fill with fresh cold water.
6. Bring clean water to a boil 2 or 3 times using cold water to rinse any residual acid taste.
7. Unplug the Kettle power base from the wall outlet.
WARNING:
• To avoid personal injury, always use extreme caution when handling hot water.
• Do not touch any Kettle surface during and after use.
• Never lift the Kettle lid when boiling water.

Storing Instructions

1. Never store the Kettle while the power base is still plugged in.
2. Unplug the Kettle and allow it to cool.
3. Store the Kettle with lid in place.
4. Never wrap cord tightly around the power base. Never place any stress on cord, especially where the
cord enters the power base, as this could cause the cord to fray and break.
5. Store Kettle and power base in its box or in a cool, dry place.

Troubleshooting

Problem Cause
The Kettle will not begin to heat. Kettle has boiled dry.
Auto Dry Protection device has
been activated.
Kettle's performance has slowed. Mineral, lime, calcium deposits
in Kettle.
The control panel interface cannot User's hands may be wet.
detect my action.
SO-315733_14762_Bella_1.8L Touch Ceramic Kettle_Amazon_IM_R8.indd 10-11
Solution
Add water to the Kettle.
Descale Kettle.
Dry hands on a towel or paper
towel prior to using the kettle's
control panel interface.
10
Limited TWO-YEAR Warranty
SENSIO Inc. hereby warrants that for a period of TWO YEARS from the date
of purchase, this product will be free from mechanical defects in material and
workmanship, and for 90 days in respect to non-mechanical parts. At its sole
discretion, SENSIO Inc. will either repair or replace the product found to be defective,
or issue a refund on the product during the warranty period.
The warranty is only valid for the original retail purchaser from the date of initial
retail purchase and is not transferable. Keep the original sales receipt, as proof of
purchase is required to obtain warranty validation. Retail stores selling this product
do not have the right to alter, modify, or in any way revise the terms and conditions of
the warranty.
EXCLUSIONS:
The warranty does not cover normal wear of parts or damage resulting from
any of the following: negligent use of the product, use of improper voltage or
current, improper routine maintenance, use contrary to the operating instructions,
disassembly, repair, or alteration by anyone other than qualified SENSIO Inc.
personnel. Also, the warranty does not cover Acts of God such as fire, floods,
hurricanes, or tornadoes.
SENSIO Inc. shall not be liable for any incidental or consequential damages caused
by the breach of any express or implied warranty. Apart from the extent prohibited
by applicable law, any implied warranty of merchantability or fitness for a particular
purpose is limited in time to the duration of the warranty. Some states, provinces or
jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts, and therefore, the
above exclusions or limitations may not apply to you. The warranty covers specific
legal rights which may vary by state, province and/or jurisdiction.

HOW TO OBTAIN WARRANTY SERVICE:

You must contact Customer Service at our toll-free number: 1-866-832-4843.
A Customer Service Representative will attempt to resolve warranty issues over
the phone. If the Customer Service Representative is unable to resolve the problem,
you will be provided with a case number and asked to return the product to SENSIO
Inc. Attach a tag to the product that includes: your name, address, daytime contact
telephone number, case number, and description of the problem. Also, include a
copy of the original sales receipt. Carefully package the tagged product with the sales
receipt, and send it (with shipping and insurance prepaid) to SENSIO Inc.'s address.
SENSIO Inc. shall bear no responsibility or liability for the returned product while in
transit to SENSIO Inc.'s Customer Service Center.
11
2018-09-13 8:45 AM