Call Functions; Technical Specifications; Care And Maintenance - Twiins D1 Manual De Instrucciones

a few seconds until the speaker provides an acoustic
signal and the LED indicator (1a) begins flashing in red
before the device powers off.

Call functions

When there is an incoming call, the speaker will provide
an acoustic signal.
Answering by pressing the button (1b): press the
control button (1b) only once
Ending a call: press the control button (1b) only once or
wait until the other person hangs up
Rejecting an incoming call: press the control button
(1b) twice, as soon as you hear the acoustic signal for
an incoming call
Redialling: press the control button (1b) twice. This
depends on the features and configuration of your
mobile phone.
Adjusting the volume
The Twiins D1 device is pre-programmed with a
®
volume level that allows for optimal listening at speeds
of up to 80 km/h (50 mph). To adjust the volume, use
the volume controls on the connected device.
Volume perception may vary depending on the position
and separation of the speakers from your ears, as
well as the type of helmet and motorcycle, external
conditions and other factors.

Technical Specifications

Bluetooth : 2.1 Class 2
®
Profiles: HSP, HFP, EDR
Battery: Lithium polymer, allowing for up to 7 hours of
talk time and 200 hours of standby time (depending on
use and configuration of the device)
Compatible with Twiins
Twiins D2HSAi intercoms
®
Ready to operate as an intercom: you can pair your
Twiins D1 device to a Twiins
®
and activate the intercom mode, without losing the
hands-free features for your phone.
Dual link: While connected to a Twiins
D2HSAi, if you receive a call, the intercom function will
stop and then resume when the call ends.
D3 and
®
D3 or a Twiins D2HSAi
® ®
D3 or Twiins
® ®

Care and maintenance

The Twiins D1 device uses components with the latest
®
technology and is manufactured to high standards.
To keep your device from inadvertently becoming
damaged, please read the following recommendations
carefully:
• Do not attempt to open any of the system
components, since the electronic parts inside it may
become damaged. Do not attempt to open or change
the battery as it may be dangerous.
• Keep the Twiins D1 out of the reach of children.
®
• Keep the Twiins D1 in a dry place. Humidity and
®
condensation may damage the electronic circuits.
• Avoid exposing the device to extreme temperatures.
Intense cold may create condensation inside the
components as these warm up. Extreme heat may
damage the battery, circuits or casings.
• Do not drop, hit or bend the components as the
internal circuits may become damaged.
• Do not paint or decorate the Twiins
may become damaged or impede correct operation.
• Do not use chemical products, solvents or detergents
to clean the Twiins D1 as these may damage the device.
®
Troubleshooting
If you cannot connect your Twiins
mobile phone:
• Make sure the Twiins D1 is switched on
®
• Make sure your mobile phone is switched on and
Bluetooth has been turned on
®
• Make sure both devices are paired
• Make sure the Twiins D1 device and your mobile
®
phone are fewer than 10 metres (32 ft.) apart
If, after this, you're still unable to pair or use the Twiins
D1 with your mobile phone, please contact the retailer
where you purchased the product.
Shortcuts
The Twiins D1 device allows you to receive calls
®
automatically (as long as this feature is supported by
your mobile phone). To do this, you need to activate
the automatic response feature in your mobile phone.
Press the control button (1b) to activate the voice
dialling function in the paired phone (the phone must be
configured to allow voice dialling, as long as the phone
supports this feature).
D1 as the casings
®
D1 device to your
®
®
9