Makita XRM03 Manual De Instrucciones página 7

WARNING:
Do not use two main batteries at the same time.
3-1. Installing or removing Slide battery cartridge (Fig. 4)
• To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click.
• If you can see the red indicator on the upper side of the
button, it is not locked completely. Install it fully until the
red indicator cannot be seen. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
• To remove the battery cartridge, withdraw it from the
tool while sliding the button on the front of the cartridge
or pressing the buttons on both sides of the cartridge.
WARNING:
Do not use two main batteries at the same time.
3-2. Installing or removing Cluster battery cartridge
(Fig. 5 - 9)
• Pull the supporting bar to allow the battery to insert to
the terminal.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the grove in the housing and slip
it into place.
• Release the supporting bar.
• To remove the battery cartridge, pull the supporting bar
and take the battery out of the terminal.
4. Return the battery compartment locker to the original
position.
5. Reduced power, distortion and a "stuttering sound" or
low battery sign
all the signs that the main battery pack needs to
replace.
Note:
The battery pack can't be charged via the supplied AC
power adaptor.
6. When low battery sign
on flashing is the time to replace the back up batteries.
Installing the Soft bended rod
antenna (Fig. 10 & 11)
Install the Soft bended rod antenna as show in the figure.
Note:
There is a click in the battery compartment designed to
store the removed antenna.
that appears on the display are
appears and an "E" keeps
Using Supplied AC power adaptor
(Fig. 12)
Remove the rubber protector and insert the adaptor plug
into the DC socket on the front side of the radio. Plug the
adaptor into a standard mains socket outlet. Whenever
the adaptor is used, the battery pack is automatically
disconnected. The AC adaptor should be disconnected
from the main supply when not in use.
Note:
When your radio has any interference in AM band by its
adaptor, please move your radio away from its AC
adaptor over 30 cm.
Operating your radio — Scan
tuning AM/FM
1. Press the Power button
2. Press the Source button
mode.
3. Press and hold the Tuning control
auto-tune. Your radio will scan up the AM/FM band
from the currently displayed frequency and will stop
scanning automatically when it finds a station of
sufficient strength.
4. After a few seconds the display will update. The
display will show the frequency of the signal found.
5. To find other station, press and hold the Tuning
control as before.
6. When the end of the waveband is reached your radio
will recommence tuning from the opposite end of the
waveband.
7. Rotate the Tuning control to
level as required.
• While adjusting the volume, make sure the FM/AM is
NOT flashing on the screen.
• If AM/FM is flashing on the screen, it allows you to
tune the stations manually (see the section of
"Manual tuning-AM/FM" for more detail).
8. To switch off your radio press the Power button
Manual tuning — AM/FM
1. Press the Power button
2. Press the Source button
mode.
3. Press the Tuning control
or AM is flashing on the display.
• FM/AM will flash approx. 10 seconds. Within this
period, only manual tuning is allowed.
• If volume adjustment is desired while FM/AM is
flashing, press the Tuning control to stop the flash
and you can rotate the Tuning control to adjust
sound level.
to switch on your radio.
to select AM or FM radio
to carry out an
adjust the sound
.
to switch on your radio.
to select AM or FM radio
and you will see the FM
7