Service Information - DeWalt DG3000 Manual De Instrucciones

CLEANING
WARNING: When cleaning, use only mild soap and a damp cloth on plastic parts. Many
household cleaners contain chemicals which could seriously damage plastic. Also, do not use
gasoline, turpentine, lacquer, paint thinner, dry cleaning fluids or similar products which may
seriously damage plastic parts. Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
The generator should be kept clean and dry at all times. The generator should not be stored
or operated in environments that include excessive moisture, dust or any corrosive vapors.
If these substances are on the generator, clean with a cloth or soft bristle brush. Do not use
a garden hose or anything with water pressure to clean the generator. Water may enter the
cooling air slots and could possibly damage the rotor, stator and the internal windings of the
alternator.
Spark Arrester
_WARNING: Risk of explosion or fire. DO NOT operate
generator without spark arrestor (TT). UU
_WARNING: ff the engine has been running, the muffler will
be very hot. To reduce the risk of injury, allow engine to cool
before proceeding.
NOTE: The spark arrester must be serviced every 100 hours
to maintain its efficiency.
1. Remove the spark arrestor screws (UU) and remove the
spark arrestor.
2. Use brush to remove carbon deposits from the spark
arrester screen. Inspect the spark arrester screen for holes
or tears. Replace the spark arrester if necessary.
_,WARNING: Always wear certified safety equipment." ANSI
Z87.1 eye protection (CAN/CSA Z94.3) with side shields when
removing carbon deposits.
Fuel Sediment Cup Cleaning
The sediment cup prevents dirt or water, which may be in the
fuel tank from entering the carburetor. If the engine has not been run for a long time, the sedi-
ment cup should be cleaned.
1. Turn the fuel shut-off valve (K) to the OFF position (horizontal to
the
ground). Remove the sediment cup (QQ), O-ring (RR) and
screen (SS) as shown.
2. Clean the sediment cup, O-ring and screen in nonflammable or ,jj.s _
high flash point solvent. _ ............... K 3. Reinstall O-ring, screen and sediment cup.
4. Turn the fuel shut-off valve to the OPEN position and check for '_- -_
fuel leaks.
Battery Pack and Charger
CHARGER CLEANING INSTRUCTIONS
_ WARNING: Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the
exterior of the charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
Engine
See engine's instruction manual for correct procedure.
, . .'b
ss '_
Q_ RR
TRANSPORTING
_ WARNING: Units are heavy, Observe safe rifting procedures when transporting.
Before transporting generator, make sure to:
1. Place engine switch in the OFF position.
2. Place the fuel valve lever on gas tank in the CLOSED position.
3. Keep generator level at all times to prevent fuel spillage. Fuel vapor or spilled fuel may
ignite.
WARNING: Contact with a hot engine or exhaust system can cause serious burns or fire.
Let the engine and muffler cool before transporting the generator.
Storage
_J,WARNING: Never store generator with fuel in the tank indoors or in enclosed, poorly venti-
lated areas, where fumes can reach an open flame, spark or pilot light as on a furnace, water
heater, clothes dryer or other gas appliances.
ENGINE
See engine's instruction manual for correct procedure.
GENERATOR
1. Clean the generator as outlined under Maintenance.
2. Check that cooling air slots and openings on generator are open and unobstructed.
BATTERY PACK
NOTE: Battery storage and carrying caps are provided for use whenever the
battery is out of the tool or charger. Make sure storage and carrying caps
are in place when storing battery pack. See Important Safety Instructions
for Battery Pack.
ACCESSORIES
Recommended accessories for use with your tool are available for purchase
from your local dealer or authorized service center. If you need assistance in locating any
accessory for your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road,
Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.
com.
_WARNING: Since accessories, other than those offered by DEWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only DEWALT, recommended accessories should be used with this product.
SERVICE INFORMATION
Please have the following information available for all service calls:
Model Number Serial Number
Date and Place of Purchase
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
performed by a DEWALT factory service center, a DEWALT authorized service center or other
qualified service personnel. Always use identical replacement parts.
FUll Two Year Warrant)/
DEWALT heavy duty generators are warranted for two years from date of purchase. We will
repair, without charge, any defects due to faulty materials or workmanship. For warranty repair
information, call 1-800-4-DEWALT. This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by others. This warranty gives you
specific legal rights and you may have other rights which vary in certain states or provinces.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained either in
the packaging, call the local company or see website for warranty information.
13