Tabla de contenido
Publicidad
6. Functions
Opening and closing by means of a hand transmitter signal,
inside switch, key switch or coded lock (see special
accessories page 51).
Transmission code manipulation protection (scan protection),
guards against the unauthorized opening of the garage door
If the door encounters an obstacle while opening or
closing, it will stop and be freed of load. The next signal
impulse will cause the door to move in the opposite direction.
The door can be stopped in any intermediate position by
sending an impulse.
After an intermediate stop, the next impulse will cause the door
to move in the opposite direction.
The self-locking drive holds the door in the closed position.
All side door locks must be removed.
The integrated lighting is automatically switched on by the
signal impulse for approx. 2,5 min.
7. Important Notes
Carefully follow the mounting and operation instructions.
Pay strict attention to Section 15 „Starting operation"
Mains connections must only be made by qualified electricians
(not included in service).
Unplug the mains cable when removing the housing cover or
when working on the drive unit.
Only use light bulbs up to 25 W.
Only activate the door opener when the garage door is in full
view and the swing-out area is clear.
Only drive in and out of the garage when the garage door is
fully open.
Keep the garage door block on the ground clean (free of snow,
ice, stones, etc.).
Only install in dry rooms - do not spray with water.
The emergency release (14.12 Special accessory) must be
installed on garages without a second exit.
In the event of a malfunction or danger, open the door by hand.
In an automobile, hold the transmitter as close as
possible to the windshield. Press the switch for at least 1
second.
Never place your hands in the guiding rails when the door
opener is installed; they may be caught and crushed.
Checking the door/door assembly: The drive is not designed
for operating doors that are difficult to open and close by hand.
For this reason, the door assembly must be checked to ensure
that the door can also be easily opened by hand. To do the
check, raise the door approx. 1 m, then let go. The door should
remain fixed in the position at which you left it i.e. neither move
down nor up. If the door does in fact move in one of the two
directions, there is a danger that the compensating springs are
not properly set. If such is the case, the door assembly will be
subjected to increased wear and there will be more
malfunctions.
Caution: lethal hazard! Do not attempt to replace, repair or
offset the compensating springs (or their mountings) that are
responsible for counteracting the weight of the door. The
reason for this is that the springs are under tension and can
cause serious injury if they are modified in any way. Also check
the entire door assembly (joints, door bearings, cable, springs
and mounting parts) for wear and possible damage. Check to
see if any rust, corrosion or cracks are present. Do not use the
door assembly when repairs and adjustment work are in need
of being carried out, as a fault in the door assembly or an
improperly aligned door can likewise lead to severe injuries.
Note: For your own personal safety, prior to installing the drive,
allow your professional garage door repair service to perform
work on the compensating springs of the door and, if
necessary, carry out any other maintenance and repair work.
8. Maintenance:
Make sure that the door release cable is not defective and is
properly adjusted.
The chain tension should be checked and readjusted
semiannually. (The chain should be slack but not sag.)
Examine the slide and the driver rings twice a year.
Inspect the door annually and adjust and lubricate as
necessary. Follow the manufacturerʼs instructions.
Note on greasing:
Grease the rails as well as the bolts in the roller (34/35) during
assembly and be sure to regrease them once a year.
Grease the rail on which the slide and the driver ring glide and
be sure to regrease once a year.
9. Note for service personnel:
When in doubt, the control circuit board and the hand transmitter
should also be sent when electronic or electrical components are
inspected at the service center.
10. Important safety instructions
CAUTION - In order to prevent serious or fatal injuries:
1. Read and follow all instructions.
2. Never let children operate the door controls or be allowed to
play with them. Keep the remote control out of the reach of
children.
3. Always keep the door opener in full view and ensure that no
persons or objects are in the direct vicinity. Do not let persons
or animals cross the path of the moving door.
4. Inspect the door opener on a monthly basis. The garage door
must return after striking a 50 mm high object on the ground.
5. If possible, use the emergency release only when the door is
closed.. Exercise caution when using the release with an
opened door. Weak or broken springs can result in the door
suddenly dropping, which can lead to serious or fatal injuries.
6. Ensure that the garage door is properly balanced - refer to the
manufacturerʼs handbook. An incorrectly aligned door can
lead to serious or fatal injuries. Permit only trained
maintenance personnel to perform repair work on the cables,
spring sets and other assembly components.
7. High torques may arise at certain points, e.g. where the door
pivots, in spite of an electronic force limitation feature. It is
essential, therefore, to follow the doorʼs movement with great
attention in order to prevent serious accidents, particularly
where children are concerned.
8. Keep these instructions for future reference
11. Important mounting instructions
CAUTION - In order to prevent serious or fatal injuries:
1. Read and follow all instructions.
2. Only mount the door opener on a properly aligned garage
door. An incorrectly aligned door could lead to serious
injuries. Permit only trained maintenance personnel to perform
repair work on the cables, spring sets and other assembly
components of the system responsible for maintaining
balance prior to mounting the opening mechanism.
3. Before you fit the opening mechanism remove or deactivate
all cables and locking devices except those which are
operated by the opening mechanism to be connected to the
garage door.
4. If possible, mount the door opener 2.1 meters or higher above
the ground and the emergency release 1.8 meters above the
ground.
5. When mounting a garage door control button, ensure that it is
a) located close to the door, (b) at a minimal height of 1.5
meters so that small children cannot reach it and (c) located
11
Publicidad
Tabla de contenido
