Double Insulation For Safer Operation - Metabo HPT WR 16SE Manual De Instrucciones

Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
10. NEVER use a power tool for applications other
than those specified.
NEVER use a power tool for applications other than
those specified in the Instruction Manual.
11. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
12. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
13. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
14. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to youself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
15. Keep motor air vent clean.
The tool's motor air vent must be kept clean so
that air can freely flow at all times. Check for dust
build-up frequently.
16. Operate power tools at the rated voltage.
Operate the power tool at voltages specified on its
nameplate.
If using the power tool at a higher voltage than
the rated voltage, it will result in abnormally fast
motor revolution and may damage the unit and
the motor may burn out.
17.
NEVER use a tool which is defective or
operating abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a metabo HPT authorized service
center.
18.
NEVER leave tool running unattended. Turn
power off.
Don't leave tool until it comes to a complete stop.
19.
Carefully handle power tools.
Should a power tool be dropped or struck
against hard materials inadvertently, it may be
deformed, cracked, or damaged.
20.
Do not wipe plastic parts with solvent. Solvents
such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and
crack plastic parts. Do not wipe them with such
solvents. Wipe plastic parts with a soft
cloth lightly dampened with soapy water and
dry thoroughly.
21. ALWAYS wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.
22. When working in high places, check there is
nobody below. During operation, take care not to
catch or tighten the cord accidentally.
23. Switch the reversing switch only after the motor
is stopped when it is necessary to change the
direction of the rotation.
24. Use a step up transformer when a long extension
cable is used.
25. Confirm the tightening torque by a torque wrench
before use in order to ascertain the correct
tightening torque to be used.
26. Attach the hex. socket securely onto the anvil. If
the hex. socket is insufficiently secured, it may drop
out and cause an accident. For hex. socket
attachment refer to "PRIOR TO OPERATION" on
page 8.
27. Confirm whether the socket has any crack in it.
28. Definitions for symbols used on this tool
V ............... volts
Hz ............. hertz
A ............... amperes
n .............. no load speed
o
W .............. watt
............ Class II Construction
---/min ...... revolutions per minute
.............. Alternating current
DOUBLE INSULATION FOR SAFER
OPERATION
To ensure safer operation of this power tool,
metabo HPT has adopted a double insulation design.
"Double insulation" means that two physically
separated insulation systems have been used to
insulate the electrically conductive materials connected
to the power supply from the outer frame handled by
the operator. Therefore, either the symbol "
words "Double insulation" appear on the power tool
or on the nameplate.
Although this system has no external grounding, you
must still follow the normal electrical safety precautions
given in this Instruction Manual, including not using the
power tool in wet environments.
To keep the double insulation system effective,
follow these precautions:
Only metabo HPT AUTHORIZED SERVICE CENTER
should disassemble or assemble this power tool,
and only genuine metabo HPT replacement
parts should be installed.
English
" or the
5