Oscartielle Phoenix 2 Serie Instrucciones De Uso página 23

The following technical data are also shown on the serial plate (FIG. 8):
1. Name and address of the manufacturer
2. Commercial name of the cabinet
3. Cabinet code
4. Cabinet serial number
5. Rating
6. Frequency
7. Max absorbed current
8. Max absorbed power
9. Max absorbed power during defrosting
10. Standard lighting power
11. Net display area
12. Type of cooling gas used
13. Weight of cooling gas loaded in each unit
14. Climatic class and reference temperature (dry bulb)
15. Electrical safety factor
16. Work schedule number
17. Work order number
18. Year of manufacture
19. Heating capacity
20. QR code
21. EAC marking
Warning: The serial plate and the warning labels must never be removed from the cabinet. The Manufacturer is not liable
for any damage or injury if this warning is ignored. The Manufacturer certifies that this unit complies with Italian legislative
degree no. 108 dated 25.01.1992, applying EEC Directive 89/109 concerning materials and objects that come into
contact with food.
7 - Loading and use of the unit (start-up)
If the display unit has been greatly tilted during positioning and installation, wait at least three hours before starting it up in
order to give the lubricating oil enough time to collect in the compressor! The refrigerating unit may be irretrievably
damaged if this precaution is ignored. The display unit can only be started up for the very first time after complying with
points 3 and 4 above.
With the unit unplugged, remove the plastic film protecting the insides and outside and then clean (follow the instructions
in point 10 below). Screw on the back spacers as shown in FIG. 11. Fit the various shelf supports at the height required,
as shown in FIG. 12 and FIG. 12B (only for Phoenix 2). FIG. 1 shows the best distances between shelves. Plug in the
unit (having followed the instructions in point 5), then switch on the lights and motor unit located under the decorative
panel (see FIG. 10). The gentle hum of the motor and illumination of the display will indicate that the cabinet is working.
The thermometer inside the display unit (see FIG. 10) will indicate the working temperature. The instruction manual for
the electronic control to which the display refers is enclosed with the instruction booklet (tampering with this device is
impossible because a password is required and only a specialized expert can intervene on it). The thermostat and gas
charge are set in the factory. Tampering with the factory settings relieves the manufacturer of any liability. Always check
that the temperature reading on the display of the electronic control is suitable for the conservation of the products placed
in the display cabinet.
The unit is designed to display food products and to maintain the temperature of the product; it does not lower it. The
product should, therefore, only be loaded once its proper storage temperature has been reached. Recommendations for
storage:
- Never block the cooling outlets that guarantee the correct flow of air (see FIG. 13).
- When loading a display cabinet that already contains products, it is best to place the new products below those
already inside (as well as observing the above points).
- At night, use the night blinds (available on request), as this will save energy and help preserve the products on
display.
8 - Prohibitions and requirements
Warning: disconnect the cabinet from the power supply in case it is not used. The power supply has to be disconnected
by the remote-control switch fitted upstream from the power socket.
Warning: Never expose the unit to the atmospheric agents. Never use direct water jets to clean the unit. Never touch or
use the unit with wet or damp feet and hands.
Warning: Never remove guards or covers that require tools to be removed. Never, under any circumstances, remove the
cover on the electronic panel.
Warning: Never load the unit excessively. Never go inside the cabinet.
Warning: Never stand on the unit or place heavy loads on top of the cabinet.
Warning: Never try to remove any ice that may build up using sharp metal objects.
Warning: The refrigerating circuit does not cause any chemical modification of the water generated from defrosting. This
comes exclusively from the vapour contained in the air circulating inside the unit. In any case, this water should always be
drained into the sewer or sent to a water purification plant in line with current local regulations.
21