Before Starting The Equipment - EINHELL TE-ID 650E Manual De Instrucciones

Anleitung TE_ID_650_E_SPK8__ 11.09.12 15:33 Seite 18
GB
Have the equipment checked if necessary.
n
Switch off the equipment when not in use.
n
Wear gloves.
n

6. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
6.1. Fitting the additional handle (Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do not
use the equipment without the additional handle.
The additional handle (8) is secured to the hammer
drill by a clamp. Turning the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
The supplied additional handle (8) must first be
n
fitted. To do this, the clamp must be opened by
turning the handle until it is wide enough for the
additional handle to be slid over the chuck (1) and
on to the hammer drill.
After you have mounted the additional handle (8),
n
swivel it to the most comfortable working position
for yourself.
Now turn the handle in the opposite direction
n
again until the additional handle is secure.
The additional handle (8) is suitable for both left-
n
handed and right-handed users.
6.2 Storage of the drill (Figure 1 / Item 10)
The additional handle (8) is equipped with a storage
compartment for drill bits (10) where you can store
drill bits of different sizes.
Turn the storage compartment (10) anti-
n
clockwise and out of the additional handle (8).
Insert the required drill bits.
n
Mount the storage compartment (10) back on the
n
additional handle. When doing so, make sure that
the pins on the inner edge of the storage
compartment (10) fit onto the recesses in the
additional handle (8).
Secure the storage compartment by turning it
n
clockwise.
18
6.3 Fitting and adjusting the depth stop
(Fig. 4-5/Item 2)
Undo the thumb screw (a) on the additional
n
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
Set the depth stop and retighten the thumb
n
screw.
Now drill the hole until the depth stop touches the
n
workpiece.
6.4 Fitting the drill bit (Fig. 6-7)
Always pull the power plug before making
n
adjustments to the equipment.
Release the depth stop as described in 6.3 and
n
push it towards the additional handle. This
provides free access to the chuck (1).
This hammer drill is equipped with a spindle lock
n
(9) and a quick-change drill chuck.
Press the spindle lock (9) and turn the drill chuck
n
(1) until it engages (see Fig. 6). Keeping the
spindle lock (9) pressed, turn the firmly closed
drill chuck (1) so that it opens (see Fig. 7). The
drill chuck opening must be large enough to take
the drill bit.
Select a suitable drill bit. Push the drill bit as far
n
as possible into the chuck opening.
Keeping the spindle lock (9) pressed, turn the drill
n
chuck (1) so that it closes. Check that the drill bit
is secure in the chuck (1).
Check at regular intervals that the drill bit or tool is
n
secure (pull the mains plug).
When the quick-change drill chuck (1) is open as
n
far as it will go (maximum drill bit opening) and
secure, press the spindle lock (9) and turn the
drill chuck (1) clockwise (viewed from the front)
until you hear a grating noise. Keeping the
spindle lock (9) pressed, turn the drill chuck (1)
approx. 5 mm in the opposite direction until you
hear a clicking noise. Then turn the drill chuck (1)
clockwise again to the desired position. This
function will prevent damage to the drill chuck.
Important.
Do not press the spindle lock (9) while the drill is in
use.