Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS –
Thank you for choosing the BELLCOME products. We will assist you throughout the entire warranty period.
For technical support and assistance you can contact us at ELECTRA Building Communications GmbH
support@bellcome.com.
KIT INSTALLATION.
Follow the steps below, in the described order.
STEP 1. Read the diagrams in this brochure and the technical manuals of the KIT (VPA, VTx, SCU).
STEP 2. Make the electrical connections to the terminals (ATM, VTM, VTA) and then to the VPA outdoor panel.
STEP 3. Make the electrical connections of the LCK door lock and LOCK SUPPLY to the terminals of the SCU central unit
and, if necessary, the connections to: the EXIT button; AUX additional installations; BAT; Vcam analog video camera.
STEP 4. AUTHORIZED PERSONNEL!!! READ THE SAFETY INSTRUCTIONS FROM THE MANUAL OF THE SCU CENTRAL
SUPPLY UNIT!!!
DISCONNECT the fuses and make the L,N,
power network. The
, S2 LEDs turn on, and S1 turns on only if the battery (12V/max. 42Ah) is connected.
STEP 5.1. PROGRAMMING THE MAIN ENTRANCE PANEL: RFID CARDS/TAGs
button (point 6). The PROG Red LED turns on
to the
(RFID) area for one second. For each programmed RFID CARD/TAG, the panel issues two beeps.
Follow the same steps for programming all the RFID CARDS/TAGs, for all the residents of the building.
Return to the SCU and short press the PROG button. The Red LED turns off. The main panel keeps address 1, which
is set from the factory and is ready to function.
EN
STEP 5.2. PROGRAMMING THE ADDITIONAL PANEL: NEW ADDRESS and RFID CARDS/TAGs. If the access in the building
is made through two entrances, the VPA2 additional panel (point 11) from entrance 2 must be set up with address 2.
At SCU 2 long press the PROG button. The PROG Red LED turns on.
(long confirmation beep), then short touch the Fam.1 key, twice. The panel confirms the storage of address 2 with
two short beeps. Continue programming the CARDS/TAGs in the VPA2 panel.
confirmed by the VPA2 with two beeps.
The VPA2 and VPA1 panels are ready to function, with all the terminals in the building.
STEP 6.1 PROGRAMMING THE ADDRESS OF THE Fam.1 TERMINAL. The terminals keep Address 1, which is set by the
manufacturer.
STEP 6.2 PROGRAMMING THE ADDRESS OF THE Fam.2, Fam.3 or more TERMINALS. The terminals for Family 2 will have
address 2, the terminals for Family 3 will have address 3 and so on for 4, 5 etc.
Program the new addresses as follows:
At the terminals for Family 2, long touch the
key twice. Two short beeps are issued. The terminal stores address 2. Continue programming address 3 at Family 3 following
the same steps. Long touch the
with three short beeps.
ready to function.
RECOMMENDED CABLES
1) Max. 75 ml
4 x 0.5 mm (H03VV-F4G 0.5)
2) Max. 150 ml
4 x 0.75 mm (H05VV-F4G 0.75)
Out of electrical safety reasons, we recommend installing a grounding cable (minimum 1.00 mm – Green/Yellow) from the
panel (VPM) to the
central unit (SCU).
DETAILED PRODUCT CODES
VPA - advanced video outdoor panel; Product codes: 1Fam.VPA.1S(F)R02.xxy04; 2Fam.VPA.2S(F)R02.xxy04;
3Fam.VPA.3S(F)R02.xxy04; 5Fam.VPA.5S(F)R02.xxy04 (S= Surface mounting, F= Flush mounting, R= RFID CARD/TAG access)
RFID access CARD/TAG (secured at reading and copying). They are stored and can be deleted from the VPM.
ATM - smart+ audio terminal; Product code: ATM.0S402.xxy04
VTM - smart+ 3.5" video terminal; Product code: VTM.3S402.xxy04
VTM/VTA - smart+/advanced 7" video terminal; Product codes: VTM.7S402.xxy04/ VTA.7S902.xxy04
VCB – Video connection box (1 video input/4 video outputs - 4 Fam.); Product code: VCB.4DN02.xxy04
Go to the VPA panel from the main entrance and touch each RFID CARD
Return to the SCU2 and short press the PROG button. The Red LED turns off.
At SCU 1 long press (3 sec.) the PROG button. The PROG Red LED turns on
key. The terminal confirms with one long beep. Short touch the
key and after the long beep, short touch the
Return to the SCU and short press the PROG button. The Red LED turns off. The terminals are
(point 1) Maintain the same wire colors for the same connections.
2
2
VIDEO DOOR PHONE KIT
connections to the SCU
At the VPA2 panel, long touch the Fam.1 key
3) Max. 250 ml
UTP cat5e (AWG24) or UTP cat6e (AWG23)
1
+43 1 810 20 99,
CONNECT the fuses to the
At the SCU, long press (3 sec.) the PROG
Each touch of the CARD/TAG to the
key three times. Storage is confirmed
2
area is
Publicidad
