Automatic Address Adjustment; Manual Address Adjustment; Control With The Led-4C; Dmx Channels - IMG STAGE LINE CPL-3DMX Manual De Instrucciones

6.2.1 Automatic address adjustment

This method is recommended when several CPL-
3DMX units are used and the first unit is to receive
start address 1:
1) On all CPL-3DMX units, set all DIP switches (2)
to the lower position (OFF)
Fig. 4 Automatic adjustment: all switches set to OFF
2) Interconnect all CPL-3DMX units via the DMX
INPUT (5) and the DMX OUTPUT (6) (
ter 6 .1) and switch them on .
3) On the first CPL-3DMX unit (directly connected
to the light controller), keep the button AUTO
DMX ADDRESS (3) pressed for five seconds until
the LEDs connected are extinguished .
After a while, the LEDs will light up again . The start
address of the first CPL-3DMX unit is now set to
1 . The start addresses of the following CPL-3DMX
units are respectively set to the next DMX address
that is free:
2 unit to address 5
nd
3 unit to address 9
rd
4 unit to address 13
th
5 unit to address 17, etc .
th

6.2.2 Manual address adjustment

The start address is adjusted as a binary number
with the DIP switches Nos . 1 – 9 (2) . It will result
by adding the place values of the switches set to
"ON" . (Switch No . 10 is without function .)
Examples of the start addresses 1, 6 and 104:
ON
OFF
Fig. 5 Start address 1: switch No. 1 set to ON
ON
OFF
Fig. 6 Start address 6: switches Nos. 3 and 2 set to ON
ON
OFF
Fig. 7 Start address 104: switches Nos. 7, 6 and 4 set to ON
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
ON
OFF
☞
Place value
Switch number
Place value
Switch number
Place value
Switch number
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®
The easiest way is to start from the highest possible
place value and to add the smaller values until the
start address will result .

6.3 Control with the LED-4C

The unit LED-4C from IMG STAGE LINE is an easy-
to-use controller which also allows to control the
CPL-3DMX . The LED-4C is equipped with 4 chan-
nels so that all units connected to it can only be
controlled synchronously .
Set the start address of the CPL-3DMX to 1
or to a multiple of 4 + 1 (5, 9, 13, ..., 61 max .),
☞ chapter 6 .2 . Detailed information for operation
chap-
can be found in the manual of LED-4C .
7 Specifications
Current rating: . . . . . . . . . .3 × 1.5 A max.
Power supply: . . . . . . . . . .12 – 24 V⎓,
No-load current: . . . . . . . .110 mA
Ambient temperature: . . . .0 – 40 °C
Dimensions: . . . . . . . . . . .193 × 40 × 72 mm
Weight: . . . . . . . . . . . . . . .460 g

7.1 DMX channels

DMX value
Channel 1: proportion of red
0 – 255
Channel 2: proportion of green
0 – 255
Channel 3: proportion of blue
0 – 255
Channel 4: simmer / music control / stroboscope
0 – 7
8 – 190
191 – 200
201 – 247
248 – 255
Subject to technical modification .
depending on the LEDs
connected
Function
brightness of red
brightness of green
brightness of blue
light off
dimmer: dark  bright
music-controlled change of colour
via integrated microphone
stroboscope: slow  fast
maximum brightness
11