Application Of Maximum/Minimum Value Inquiry Mode; Application Of Data Hold And Zero Calibration Mode; Other Functions; Auto Power-Off - ELCART NI 2610 Manual De Usuario

ART. 09/07910-00

3.3 Application of maximum/minimum value inquiry mode

Press and hold "MAX/MIN" key for a short time, "MAX" will appear on top
In max/min value inquiry mode, press "MAX/MIN" key once, you will switch
Press and hold "MAX/MIN" for one second, "MAX/MIN" on top LCD
interface will disappear, and the max/min value inquiry mode will exit.
Tips
In non-zero calibration mode, press and hold "MAX/MIN" key for a short

3.4 Application of data hold and zero calibration mode

Press and hold "HOLD/ZERO" key for a short time, "HOLD" will appear
on the top left position of the LCD interface (as shown in 3-1-4A), then the
Press and hold the key again, "HOLD" on the top left position of the LCD
Cover the opto-sensor with the visor, and press and hold "HOLD/ZERO"
key for one second, "ADJ" will appear on LCD interface (as shown in
Several seconds later, "ADJ" on LCD interface will disappear, and zero
calibration mode will automatically exit and return to auto measurement
mode.
Notice
Before zero calibration, the opto-sensor must be covered with the opto-
sensor visor.
Tips
1. In non-zero calibration mode, press and hold "HOLD/ZERO" key for a
short time to enter the data hold mode.
2. Zero-calibration can be made in any mode.

4 Other Functions

4.1 Auto power-off

If there is no action on keys of the for a long time, the meter will automatically
power off about 10 minutes later.
ELCART DISTRIBUTION SPA via Michelangelo Buonarroti, 46 - 20093 Cologno Monzese (Milano) ITALY
Tel. +39 02.25117310 Fax +39 02.25117610 sito internet: www.elcart.com
La divulgazione dei dati contenuti in questa scheda è da ritenersi un servizio puramente informativo e non costituisce alcun vincolo da parte della Elcart in merito a prestazioni ed utilizzo del prodotto.
The divulgation of data contained on this technical sheet are exclusively for informational reasons and establish no link on behalf of Elcart regard to thr performances and the usa of the product.
La divulgacion de los datos contenidos en esta ficha son un servicio unicamente informativo y no constituyen ningun vinculo de parte de Elcart respecto a las prestaciones y uso del producto.
ELCART
Manuale di istruzioni/Scheda tecnica

5 Technical Data

Temperature range:
Operation:-10°C÷+50°C, max 80% HR (Non-Condensed)
Storage:-10°C÷+50°C max 80% HR (Non-Condensed) (removing
batteries)
Sensor: silicon photoelectric diode
Measured spectral range: 320÷730nm
Measurement ranges:
20, 200, 2.000, 20.000, 200.000 Lux
20, 200, 2.000, 20.000 FC
Operating environment: indoor use
Height: 2000mt. highest
Battery life: Approx. 200 hours
Power supply: 1x9 V, IEC 6LR61
Dimensions (HxWxD): 190 x 89 x 42,5 mm
Weight:
Approx. 360 gr. without batteries
Approx. 420 gr. with batteries
Accuracy: ±3% (calibrated with incandescent lamps in 2854K)
±6% other visible light source
Tips: cosine angle is corrected in accordance with JIS C 1609:1993 and
Luminous sensitivity characteristics:
6 Maintenance and Service

6.1 Service

Notice
When the meter seemingly fails during operation, following steps should
be followed to check the fault problem:
1. Check up batteries. If "
should be replaced.
2. Refer to the operation instructions to check if operation steps are wrong.
3. Before sending the meter to manufacturer for repair, the user should
remove out the batteries and describe faults in details, and pack the
meter to avoid damages in transportation. Our company will assume no
responsibility for damages in transformation.
4. Repair on the meter should be performed by service centers or other

6.2 Cleaning

First wipe the meter with a damp soft cloth with clean water or neutral
detergent and then with a dry cloth.
Notice
1. Please make sure the light meter is turned off before cleaning.
2. Do not use benzene, alcohol, acetone, ethyl ether, ketones, thinners
and gasoline, etc. in cleaning, because they will transform or fade the
light meter.
3. The light meter can only be used again when it is completely dry after
cleaning.
Cosine angle deviation characteristics
Cosine angle
30°
60°
" appears on the LCD display, batteries
- +
PAGINA 9 DI 15
Deviations
±2%
±6%
e-mail: info@elcart.it