Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-BD 750 E Manual De Instrucciones

Taladro de columna
Ocultar thumbs Ver también para TE-BD 750 E:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 101
6.9 Drill table and roll base (Fig. 29)
Slacken the clamping screw (29) to turn the
drill table (4).
Slacken the thumb screws to extend the roll
base (3).
6.10 Clamping the workpiece (Fig. 29)
As a general rule, use a machine vice or another
suitable clamping device to secure a workpiece in
position. Never hold the workpiece in place with
your hand! When drilling, the workpiece should
be able to travel on the drill table (4) for self-
centering purposes. Ensure that the workpiece
cannot rotate. This is best achieved by placing the
workpiece /machine vice on a sturdy block.
Caution! Sheet metal parts must be clamped in
to prevent them from being torn up. Properly set
the height and angle of the drill table for each
workpiece. There must be enough distance bet-
ween the upper edge of the workpiece and the tip
of the drill bit.
6.11 LED lamp (Figs. 1, 2)
The table drill is equipped with an LED lamp for
illuminating the work area. This can be switched
ON and OFF by the switch (20).
6.12 Working speeds
Ensure that you drill at the proper speed. Drill
speed is dependent on the diameter of the drill bit
and the material in question.
The table below acts as a guide for selecting the
proper speed for various materials.
Note: The drill speeds specifi ed are merely
suggested values.
Anl_TE_BD_750_E_SPK9.indb 27
Anl_TE_BD_750_E_SPK9.indb 27
GB
Drill bit Ø Cast iron
Steel Iron Aluminium Bronze
3
2550
1600
4
1900
1200
5
1530
955
6
1270
800
7
1090
680
8
960
600
9
850
530
10
765
480
11
700
435
12
640
400
13
590
370
14
545
340
16
480
300
18
425
265
20
380
240
22
350
220
25
305
190
6.13 Countersinking and center-drilling
With this table drill, you can also countersink and
center-drill. Please observe that countersinking
should be performed at the lowest speed, while a
high speed is required for center-drilling.
6.14 Drilling wood
Please note that sawdust must be properly eva-
cuated when working with wood, as it can pose
a health hazard. Ensure that you wear a suitable
dust mask when performing work that generates
dust.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
The table drill is to a large extent mainte-
nance-free. Keep the device clean. Pull out
the mains plug before doing any cleaning and
maintenance work on the machine. Do not
- 27 -
2230
9500
8000
1680
7200
6000
1340
5700
4800
1100
4800
4000
960
4100
3400
840
3600
3000
740
3200
2650
670
2860
2400
610
2600
2170
560
2400
2000
515
2200
1840
480
2000
1700
420
1800
1500
370
1600
1300
335
1400
1200
305
1300
1100
270
1150
950
06.02.2018 10:25:31
06.02.2018 10:25:31

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

42.507.15

Tabla de contenido