Cut-Off Machine Safety Warnings; Standard Accessories - HIKOKI CC 14SF Instrucciones De Manejo

English
CUT-OFF MACHINE SAFETY
WARNINGS
1. Inspect the cutting wheel before use, do not use chipped
or otherwise defect cutting wheels. Always make a trial
run before use to confi rm that the Cut-off Machine does
not involve abnormalities.
2. Use the normal cut-off wheel on its normal working
surface.
3. Guard against cut-off sparks.
4. Properly replace the cut-off wheel.
5. Always pay attention that the cut-off wheel clamping
parts are never impaired. Defective parts will cause
damage to the cut-off wheel.
6. Ensure that the workpiece is free of foreign matter such
as nails.
7. Use only cutting wheels recommended by the
manufacturer which have a marked speed equal to or
greater than the speed marked on the nameplate of the
machine.
8. Abrasive wheels shall be stored and handled with care in
accordance with manufacturer's instructions.
DESCRIPTION OF NUMBERED ITEMS (Fig. 1 - Fig. 11)
1 Wheelcover
2 Sub-cover (B)
3 Motor
4 Cut-off wheel
5 Handle
6 Spark chute
7 Sub-cover (A)
8 Stopper
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
CC14SF : Cut-Off Machine
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
9 Trigger
0 Switch stopper
! Shaft
@ Hex. bar wrench
When setting at an
#
angle of 0°
When setting at an
$
angle of 30°
When setting at an
%
angle of 45°
^ Vise (B)
9. Ensure that mounted wheel are fi tted in accordance with
the manufacture's instructions.
10. Do never use the machine without the guard in place.
Always use the blade guard. A blade guard protects
the user against broken off parts of the cutting disc and
against accidental touching of the cutting disc.
11. Make sure that the guard operates properly and that it
can move freely. Never lock the guard in place when
opened.
12. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
13. If the cutting disc becomes jammed, switch the machine
off and watt until the cutting disc comes to a complete
stop. Never attempt to remove a still running cutting
disc from the cut, otherwise there is danger of kickback.
Determine and correct the cause for the jamming.
14. Do not use saw blade.
15. Do not use the machine in explosive atmospheres and
environments where sparks could fi re, explosion etc.
16. Store the machine in a safe manner when not being
used. The storage location must be dry and lockable.
This prevents the machine from storage damage, and
from being operated by untrained persons.
& 10 mm bolts
Steel board (More than
*
thickness 6 mm)
Flat hd. screw of more
(
than 6 mm × 15
) 6 mm nuts
The vise-jaws open to
170 mm while the vise
q
can be set in two steps
205 mm and 240 mm.
w Vise (A)
Dimension of workpiece
e
to be cut
r Metallic block
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
○ Cut-off wheel ................................................................1
○ Hex. bar wrench ...........................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting of various metallic materials such as pipes, round
bars, shaped steel and siding board.
4
Dimension of Metallic
t
block
y Clutch
u Screw handle
i Workpiece material
o Carbon Brush
p Wear limit
a No. of carbon brush